SUPER MICRO Computer X7DBi+ IDE Channel 0 Master/Slave and IDE Secondary Master/Slave, Type

Page 60

X7DBi+ User's Manual

IDE Channel 0 Master/Slave and IDE Secondary Master/Slave

These settings allow the user to set the parameters of the slots specified. Press <Enter> to activate the following submenu items for detailed options. Set the correct configurations accordingly.

Type

This item allows you to select the type of IDE hard drive. Select Auto to allow the BIOS to automatically set the HDD's capacity, number of heads, etc. Enter a number from 1-39 to select a type of hard drive. Select User to allow the user to enter the parameters of the HDD installed at this connection. Select CDROM if a CDROM drive is installed. Select ATAPI if a removable disk drive is installed.

Multi-Sector Transfers

This item allows the user to specify the number of sectors per block to be used in multi-sector transfer. The options are Disabled, 4 Sectors, 8 Sectors, and 16 Sectors.

LBA Mode Control

This item determines whether the Phoenix BIOS will access the IDE Channel 0 Master Device via the LBA mode. The options are Enabled and Disabled.

32 Bit I/O

This option allows the user to enable or disable the function of 32-bit data transfer. The options are Enabled and Disabled.

Transfer Mode

This option allows the user to set the transfer mode. The options are Standard, Fast PIO1, Fast PIO2, Fast PIO3, Fast PIO4, FPIO3/DMA1 and FPIO4/DMA2.

Ultra DMA Mode

This option allows the user to select Ultra DMA Mode. The options are Disabled, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4, and Mode 5.

Parallel ATA

This setting allows the user to enable or disable the function of Parallel ATA. The options are Disabled, and Enabled.

Serial ATA

This setting allows the user to enable or disable the function of Serial ATA. The options are Disabled and Enabled.

4-4

Image 60
Contents Super Manual Revision Release Date June 25 About This Manual Manual OrganizationConventions Used in the Manual PrefaceTable of Contents Table of Contents Main Bios Setup Security Setup Boot Setup ExitChecklist OverviewIntroduction Contacting Supermicro HeadquartersX7DBi+ Image X7DBi+ Motherboard Layout Not drawn to scaleJumper Description Default Setting Quick Reference X7DBi+Memory ChipsetExpansion Slots PC Health MonitoringAcpi Features DimensionsOnboard I/O OtherBlock Diagram of the 5000P Chipset 5000PChipset Overview Xeon Dual Core ProcessorsXeon Quad Core Processors Special Features PC Health MonitoringAcpi Features Slow Blinking LED for Suspend-State IndicatorMain Switch Override Mechanism External Modem Ring-OnPower Supply Super I/OPage Page Precautions InstallationStatic-Sensitive Devices UnpackingProcessor and Heatsink Installation Installation of the LGA771 ProcessorPage Installation of the Heatsink To Un-install the HeatsinkCEK Heatsink Installation Mounting the Motherboard in the Chassis Installing DIMMs Dimm InstallationMemory Support Dimm Module Population ConfigurationInstalling and Removing DIMMs Control Panel Connectors/IO Ports Back Panel Connectors/IO PortsJF1 Header Pins Power ButtonFront Control Panel Power LED Power LED Pin Definitions JF1Front Control Panel Pin Definitions NMI Button NMI Button Pin Definitions JF1NIC1/NIC2 LED Indicators Pin# Definition 13 +5V HD ActivePin# Definition Vcc 10/12 Ground Power Fail LED Overheat/Fan Fail LED OHOH/Fan Fail LED PWR Supply FailReset Button Power ButtonReset Button B. PWR Button Reset Button Pin Definitions JF1Connecting Cables ATX Power ConnectorProcessor Power Connector Universal Serial Bus USB Chassis IntrusionBackpanel USB Front Panel USBFan Headers KeylockFan Fan 7 CPU Fan Fan 8 CPU Fan Fan Header Pin Definitions Fan1-8COM1 is a connector located on ATX PS/2 Keyboard and PS/2 Mouse PortsSerial Ports Pin 10 is available on COM2 only. NC No ConnectionWake-On-Ring Wake-On-LANWake-On-Ring Pin Definitions WOR Wake-On-LAN Pin Definitions WOLPower LED/Speaker Speaker ConnectorGlan 1/2 Giga-bit Ethernet Ports PWR LED/SpeakerPower Fault PWR Supply Failure Alarm ResetPower Fault B. Alarm Reset Alarm ResetSMBus PS I2C Connector SMB J18 PWR SMB J17SMB Header Pin Definitions Pin# Definition Data Ground Clock No ConnectionVGA Connector Sgpio HeadersThere are two T-SGPIO Serial General LocationCompact Flash Card PWR Connector Compact Flash Card PWR ConnectorJumper Definition Compact Flash Power On Off Power Off Compact Flash PWRJumper Settings Glan Enable/DisableGlan Port1 Enable B. Glan Port2 Enable Explanation JumpersWatch Dog Enable/Disable Clear Cmos Watch Dog EnableWatch Dog Jumper Settings JWD Cmos Clear3rd PWR Supply PWR Fault Detect J3P VGA Enable/Disable3rd PWR Fail B. VGA Enabled 3rd PWR Supply PWR Fault Jumper SettingsCompact Flash Master/Slave Select I2C Bus to PCI-X/PCI-Exp. SlotsCompact Flash Master/ Slave Select J27Onboard Indicators Onboard Power LEDGlan LEDs Rear ViewOverheat LED/Fan Fail JOH1 Overheat LEDOverheat LED Pin Definitions OH/Fan Fail LEDConnector Parallel Printer PortParallel printer port is Located On the IO panel. See the table onFloppy Connector Simlp SlotFloppy Simlp IDE Connectors Compact Flash Card SlotTroubleshooting Procedures Before Power OnNo Power Losing the System’s Setup ConfigurationTechnical Support Procedures Memory ErrorsFrequently Asked Questions Troubleshooting System first boots up System configurationReturning Merchandise for Service System Bios How To Change the Configuration DataStarting the Setup Utility BiosRunning Setup Main Bios SetupPress the Delete key to enter Setup Main Bios Setup Menu LBA Mode Control Transfer ModeUltra DMA Mode IDE Channel 0 Master/Slave and IDE Secondary Master/SlaveSata Controller Mode Serial ATA Sata RAID EnableICH RAID Code Base Available when Sata RAID is enabled Sata Ahci Available when Sata RAID is disabledAdvanced Setup Power Loss Control Memory Cache Cache System Bios AreaCache Video Bios Area Resume On Modem RingCache Base 512K-640K Cache Extended MemoryDiscrete Mtrr Allocation PCI ConfigurationDefault Primary Video Adapter Emulated IRQ SolutionsPCI Parity Error Forwarding Reset Configuration DataEnable Master Latency TimerLarge Disk Access Mode Serr Signal Condition Memory Branch ModeAdvanced Chipset Control 4GB PCI Hole GranularityHigh Temperature Dram Operation Crystal Beach FeaturesClock Spectrum Feature AMB Thermal SensorUSB Function Legacy USB SupportFrequency Ratio Available when supported by the CPU Core-Multi-Processing Available when supported by the CPUMachine Checking Available when supported by the CPU Thermal Management 2 Available when supported by the CPUHardware Prefetch Available when supported by the CPU Direct Cache Access Available when supported by the CPUDCA Delay Clocks Available when supported by the CPU Intel Eist Support Available when supported by the CPUI/O Device Configuration KBC Clock InputSerial Port a Base I/O AddressDMA Channel Floppy Disk ControllerDMI Event Logging Event Log ValidityConsole Redirection COM Port AddressBaud Rate Console TypeCPU Overheat Alarm Peci Agent 1/2 Temperatures/System TemperatureHardware Monitoring System Temperature Fan1-Fan8 SpeedsFan Speed Control Modes Voltage MonitoringBios Post Errors Bios Post Watch DogSystem Event Logging Clear System Event LoggingOS Boot Watch Dog Timer for Loading OS MinutesSystem Event Log/System Event Log List Mode Time Out OptionRealtime Sensor Data IPMI LAN ConfigurationDefault Gateway Update LAN SettingsVlan Tagging IP Address SourceSecurity Settings Boot Settings Boot Priority Order/Excluded from Boot OrdersExit Page Bios Error Beep Codes Error MessageBeep Code DescriptionX7SBi+ User’s Manual Appendix B Installing the Windows OS Page Installing Other Drivers Appendix C Installing Other Software Programs and DriversDriver/Tool Installation Display Screen Configuring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control