SMC Networks SMC8848M manual Connecting to a Power Source, Power Socket

Page 48

INSTALLING THE SWITCH

Connecting to a Power Source

To connect a device to a power source:

1.Insert the power cable plug directly into the socket located at the back of the device.

Figure 3-8 Power Socket

2.Plug the other end of the cable into a grounded, 3-pin, AC power source.

Note: For international use, you may need to change the AC line cord. You must use a line cord set that has been approved for the socket type in your country.

3.Check the front-panel LEDs as the device is powered on to be sure the Power LED is on. If not, check that the power cable is correctly plugged in.

4.If you have purchased a Redundant Power Supply, connect it to the switch and to an AC power source now, following the instructions included with the package.

3-12

Image 48

Contents TigerStack II 10/100/1000 Page TigerStack II 10/100/1000 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Compliances FCC Class aIndustry Canada Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC Safety Compliance Power Cord SafetyAustralia AS/NZS 3548 1995 Class a Warnhinweis Faseroptikanschlüsse Optische SicherheitPower Cord Set Vii France et Pérou uniquementViii SchukoEnvironmental Statement Purpose AudienceRelated Publications Table of Contents Making Network Connections XiiAppendices XiiiGlossary Index XivTables Figures XviChapter About OverviewSwitch Architecture Front PanelsDescription of Hardware Network Management Options10/100/1000BASE-T Ports SFP Slots Gigabit Ethernet Module SlotsStacking Ports Port and System Status LEDs Port LEDs Port Status LEDsSystem LEDs System Status LEDsDescription of Hardware Optional Redundant Power Supply Power Supply SocketsOptional Media Extender Module 10GBASE XFP ModuleFeatures and Benefits ConnectivityExtender Module LEDs Module LEDsExpandability PerformanceManagement Introduction to Switching Chapter Network PlanningApplication Examples Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsEquipment Checklist Package ContentsOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an Optional Module into the Switch Installing an Optional ModuleInserting an SFP Transceiver into a Slot Optional TranscieversConnecting Switches in a Stack Making Stacking Connections Stacking Topologies Connecting to a Power Source Power SocketConnecting to the Console Port Wiring Map for Serial CableWiring Map for Serial Cable Installing the Switch Connecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsNetwork Wiring Connections Wiring Closet ConnectionsFiber Optic SFP Devices Gbps Fiber Optic Connections Making Connections to SFP TransceiversMaking Network Connections Connecting to an XFP Transceiver Connectivity Rules 1000BASE-T Cable RequirementsGbps Ethernet Collision Domain Maximum 10GBASE-SR 10 Gigabit Ethernet Cable LengthMbps Gigabit Ethernet Collision Domain Mbps Fast Ethernet Collision Domain Mbps Ethernet Collision DomainMaximum 1000BASE-ZX Fiber Optic Cable Length Maximum Fast Ethernet Cable LengthCable Labeling and Connection Records Making Network Connections Appendix a Troubleshooting Diagnosing Switch IndicatorsTable A-1 Troubleshooting Chart Diagnosing Power Problems with the LEDs Table A-2 Power/RPS LEDsPower and Cooling Problems InstallationIn-Band Access Stack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI and MDI-X Port PinoutsStraight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover WiringCable Testing for Existing Category 5 Cable 1000BASE-T Pin AssignmentsTable B-2 1000BASE-T MDI and MDI-X Port Pinouts Adjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsAppendix C Specifications Physical CharacteristicsSwitching Database WeightTemperature Power SupplySwitch Features Management FeaturesSafety StandardsCompliances CE Mark EmissionsWarranty Extender Modules10G Extender Module XFP Specifications Appendix D German Instructions Eine Site Auswählen Selecting a Site GermanMontage Rack Mounting Instructions German Rack-MontageGerman Instructions Montage Rack Mounting Instructions German Appendix E Ordering Information Ordering Information Glossary Glossary-11000BASE-T Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Transmission Control Protocol/Internet Protocol TCP/IPVirtual LAN Vlan Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call