SMC Networks SMC8848M manual Fiber Optic SFP Devices

Page 54

MAKING NETWORK CONNECTIONS

Fiber Optic SFP Devices

An optional Gigabit SFP transceiver (1000BASE-SX, 1000BASE-LX or 1000BASE-ZX) can be used for a backbone connection between switches, or for connecting to a high-speed server.

Each single-mode fiber port requires 9/125 micron single-mode fiber optic cable with an LC connector at both ends. Each multimode fiber optic port requires 50/125 or 62.5/125 micron multimode fiber optic cabling with an LC connector at both ends.

Warning: These switches use lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

Note: When selecting a fiber SFP device, considering safety, please make sure that it can function at a temperature that is not less than the recommended maximum operational temperature of the product. You must also use an approved Laser Class 1 SFP transceiver.

Hinweis: Bei der Wahl eines Glasfasertransceivers muß für die Beurteilung der Gesamtsicherheit beachtet werden, das die maximale Umgebungstemperatur des Transceivers für den Betrieb nicht niedriger ist als die für dieses Produkts. Der Glasfasertransceiver muß auch ein überprüftes Gerät der Laser Klasse 1 sein.

1.Remove and keep the LC port’s rubber cover. When not connected to a fiber cable, the rubber cover should be replaced to protect the optics.

2.Check that the fiber terminators are clean. You can clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened with a little ethanol. Dirty fiber terminators on fiber cables will impair the quality of the light transmitted through the cable and lead to degraded performance on the port.

4-4

Image 54
Contents TigerStack II 10/100/1000 Page TigerStack II 10/100/1000 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Industry Canada Class a CompliancesFCC Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC Australia AS/NZS 3548 1995 Class a Safety CompliancePower Cord Safety Warnhinweis Faseroptikanschlüsse Optische SicherheitPower Cord Set Vii France et Pérou uniquementViii SchukoEnvironmental Statement Purpose AudienceRelated Publications Table of Contents Making Network Connections XiiAppendices XiiiGlossary Index XivTables Figures XviChapter About OverviewSwitch Architecture Front PanelsDescription of Hardware Network Management Options10/100/1000BASE-T Ports SFP Slots Gigabit Ethernet Module SlotsStacking Ports Port and System Status LEDs Port LEDs Port Status LEDsSystem LEDs System Status LEDsDescription of Hardware Optional Media Extender Module Optional Redundant Power SupplyPower Supply Sockets 10GBASE XFP ModuleExtender Module LEDs Features and BenefitsConnectivity Module LEDsExpandability PerformanceManagement Introduction to Switching Chapter Network PlanningApplication Examples Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsEquipment Checklist Package ContentsOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an Optional Module into the Switch Installing an Optional ModuleInserting an SFP Transceiver into a Slot Optional TranscieversConnecting Switches in a Stack Making Stacking Connections Stacking Topologies Connecting to a Power Source Power SocketConnecting to the Console Port Wiring Map for Serial CableWiring Map for Serial Cable Installing the Switch Twisted-Pair Devices Connecting Network DevicesChapter Making Network Connections Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsNetwork Wiring Connections Wiring Closet ConnectionsFiber Optic SFP Devices Gbps Fiber Optic Connections Making Connections to SFP TransceiversMaking Network Connections Connecting to an XFP Transceiver Gbps Ethernet Collision Domain Connectivity Rules1000BASE-T Cable Requirements Maximum 10GBASE-SR 10 Gigabit Ethernet Cable LengthMbps Gigabit Ethernet Collision Domain Maximum 1000BASE-ZX Fiber Optic Cable Length Mbps Fast Ethernet Collision DomainMbps Ethernet Collision Domain Maximum Fast Ethernet Cable LengthCable Labeling and Connection Records Making Network Connections Appendix a Troubleshooting Diagnosing Switch IndicatorsTable A-1 Troubleshooting Chart Diagnosing Power Problems with the LEDs Table A-2 Power/RPS LEDsPower and Cooling Problems InstallationIn-Band Access Stack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI and MDI-X Port PinoutsStraight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover WiringCable Testing for Existing Category 5 Cable 1000BASE-T Pin AssignmentsTable B-2 1000BASE-T MDI and MDI-X Port Pinouts Adjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsAppendix C Specifications Physical CharacteristicsTemperature Switching DatabaseWeight Power SupplySwitch Features Management FeaturesCompliances SafetyStandards CE Mark EmissionsWarranty Extender Modules10G Extender Module XFP Specifications Appendix D German Instructions Eine Site Auswählen Selecting a Site GermanMontage Rack Mounting Instructions German Rack-MontageGerman Instructions Montage Rack Mounting Instructions German Appendix E Ordering Information Ordering Information Glossary Glossary-11000BASE-T Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Transmission Control Protocol/Internet Protocol TCP/IPVirtual LAN Vlan Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call