SMC Networks SMC8848M manual Making Network Connections

Page 56

MAKING NETWORK CONNECTIONS

Warning: These switches use lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

Note: When selecting a fiber device, considering safety, please make sure that it can function at a temperature that is not less than the recommended maximum operational temperature of the product. You must also use an approved Laser Class 1 SFP transceiver.

Hinweis: Bei der Wahl eines Glasfasertransceivers muß für die Beurteilung der Gesamtsicherheit beachtet werden, das die maximale Umgebungstemperatur des Transceivers für den Betrieb nicht niedriger ist als die für dieses Produkts. Der Glasfasertransceiver muß auch ein überprüftes Gerät der Laser Klasse 1 sein.

1.Remove and keep the port’s protective cover. When not connected to a fiber cable, the cover should be replaced to protect the optics.

2.Check that the fiber terminators are clean. You can clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened with a little ethanol. Dirty fiber terminators on fiber cables will impair the quality of the light transmitted through the cable and lead to degraded performance on the port.

3.Connect one end of the cable to the LC port on the switch and the other end to the LC port on the other device. Since LC connectors are keyed, the cable can be attached in only one orientation.

4-6

Image 56
Contents TigerStack II 10/100/1000 Page TigerStack II 10/100/1000 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Compliances FCC Class aIndustry Canada Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC Safety Compliance Power Cord SafetyAustralia AS/NZS 3548 1995 Class a Warnhinweis Faseroptikanschlüsse Optische SicherheitPower Cord Set Vii France et Pérou uniquementViii SchukoEnvironmental Statement Related Publications PurposeAudience Table of Contents Making Network Connections XiiAppendices XiiiGlossary Index XivTables Figures XviChapter About OverviewSwitch Architecture Front Panels10/100/1000BASE-T Ports Description of HardwareNetwork Management Options Stacking Ports SFP SlotsGigabit Ethernet Module Slots Port and System Status LEDs Port LEDs Port Status LEDsSystem LEDs System Status LEDsDescription of Hardware Optional Redundant Power Supply Power Supply SocketsOptional Media Extender Module 10GBASE XFP ModuleFeatures and Benefits ConnectivityExtender Module LEDs Module LEDsManagement ExpandabilityPerformance Introduction to Switching Chapter Network PlanningApplication Examples Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an Optional Module into the Switch Installing an Optional ModuleInserting an SFP Transceiver into a Slot Optional TranscieversConnecting Switches in a Stack Making Stacking Connections Stacking Topologies Connecting to a Power Source Power SocketWiring Map for Serial Cable Connecting to the Console PortWiring Map for Serial Cable Installing the Switch Connecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsNetwork Wiring Connections Wiring Closet ConnectionsFiber Optic SFP Devices Gbps Fiber Optic Connections Making Connections to SFP TransceiversMaking Network Connections Connecting to an XFP Transceiver Connectivity Rules 1000BASE-T Cable RequirementsGbps Ethernet Collision Domain Maximum 10GBASE-SR 10 Gigabit Ethernet Cable LengthMbps Gigabit Ethernet Collision Domain Mbps Fast Ethernet Collision Domain Mbps Ethernet Collision DomainMaximum 1000BASE-ZX Fiber Optic Cable Length Maximum Fast Ethernet Cable LengthCable Labeling and Connection Records Making Network Connections Table A-1 Troubleshooting Chart Appendix a TroubleshootingDiagnosing Switch Indicators Diagnosing Power Problems with the LEDs Table A-2 Power/RPS LEDsIn-Band Access Power and Cooling ProblemsInstallation Stack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI and MDI-X Port PinoutsStraight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover WiringTable B-2 1000BASE-T MDI and MDI-X Port Pinouts Cable Testing for Existing Category 5 Cable1000BASE-T Pin Assignments Adjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsAppendix C Specifications Physical CharacteristicsSwitching Database WeightTemperature Power SupplySwitch Features Management FeaturesSafety StandardsCompliances CE Mark Emissions10G Extender Module XFP WarrantyExtender Modules Specifications Appendix D German Instructions Eine Site Auswählen Selecting a Site GermanMontage Rack Mounting Instructions German Rack-MontageGerman Instructions Montage Rack Mounting Instructions German Appendix E Ordering Information Ordering Information 1000BASE-T GlossaryGlossary-1 Glossary-2 Glossary-3 Glossary-4 Glossary-5 Virtual LAN Vlan Glossary-6Transmission Control Protocol/Internet Protocol TCP/IP Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call