SMC Networks SMC8848M manual Power Cord Set

Page 10

COMPLIANCES

This unit operates under SELV (Safety Extra Low Voltage) conditions according to

IEC 60950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions.

France and Peru only

This unit cannot be powered from ITsupplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary connection point labelled Neutral, connected directly to earth (ground).

Impédance à la terre

Important! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following:

Power Cord Set

U.S.A. and Canada

The cord set must be UL-approved and CSA certified.

 

 

 

The minimum specifications for the flexible cord are:

 

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

 

- Type SV or SJ

 

- 3-conductor

 

 

 

The cord set must have a rated current capacity of at least 10 A

 

 

 

The attachment plug must be an earth-grounding type with NEMA

 

5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

 

 

Denmark

The supply plug must comply with Section 107-2-D1, Standard

 

DK2-1a or DK2-5a.

 

 

Switzerland

The supply plug must comply with SEV/ASE 1011.

 

 

U.K.

The supply plug must comply with BS1363 (3-pin 13 A) and be

 

fitted with a 5 A fuse which complies with BS1362.

 

 

 

The mains cord must be <HAR> or <BASEC> marked and be of

 

type HO3VVF3GO.75 (minimum).

 

 

Europe

The supply plug must comply with CEE7/7 (“SCHUKO”).

 

 

 

The mains cord must be <HAR> or <BASEC> marked and be of

 

type HO3VVF3GO.75 (minimum).

 

 

 

IEC-320 receptacle.

 

 

vi

Image 10
Contents TigerStack II 10/100/1000 Page TigerStack II 10/100/1000 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Industry Canada Class a CompliancesFCC Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC Australia AS/NZS 3548 1995 Class a Safety CompliancePower Cord Safety Warnhinweis Faseroptikanschlüsse Optische SicherheitPower Cord Set Vii France et Pérou uniquementViii SchukoEnvironmental Statement Audience PurposeRelated Publications Table of Contents Making Network Connections XiiAppendices XiiiGlossary Index XivTables Figures XviChapter About OverviewSwitch Architecture Front PanelsNetwork Management Options Description of Hardware10/100/1000BASE-T Ports Gigabit Ethernet Module Slots SFP SlotsStacking Ports Port and System Status LEDs Port LEDs Port Status LEDsSystem LEDs System Status LEDsDescription of Hardware Optional Media Extender Module Optional Redundant Power SupplyPower Supply Sockets 10GBASE XFP ModuleExtender Module LEDs Features and BenefitsConnectivity Module LEDsPerformance ExpandabilityManagement Introduction to Switching Chapter Network PlanningApplication Examples Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an Optional Module into the Switch Installing an Optional ModuleInserting an SFP Transceiver into a Slot Optional TranscieversConnecting Switches in a Stack Making Stacking Connections Stacking Topologies Connecting to a Power Source Power SocketWiring Map for Serial Cable Connecting to the Console PortWiring Map for Serial Cable Installing the Switch Twisted-Pair Devices Connecting Network DevicesChapter Making Network Connections Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsNetwork Wiring Connections Wiring Closet ConnectionsFiber Optic SFP Devices Gbps Fiber Optic Connections Making Connections to SFP TransceiversMaking Network Connections Connecting to an XFP Transceiver Gbps Ethernet Collision Domain Connectivity Rules1000BASE-T Cable Requirements Maximum 10GBASE-SR 10 Gigabit Ethernet Cable LengthMbps Gigabit Ethernet Collision Domain Maximum 1000BASE-ZX Fiber Optic Cable Length Mbps Fast Ethernet Collision DomainMbps Ethernet Collision Domain Maximum Fast Ethernet Cable LengthCable Labeling and Connection Records Making Network Connections Diagnosing Switch Indicators Appendix a TroubleshootingTable A-1 Troubleshooting Chart Diagnosing Power Problems with the LEDs Table A-2 Power/RPS LEDsInstallation Power and Cooling ProblemsIn-Band Access Stack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI and MDI-X Port PinoutsStraight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover Wiring1000BASE-T Pin Assignments Cable Testing for Existing Category 5 CableTable B-2 1000BASE-T MDI and MDI-X Port Pinouts Adjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsAppendix C Specifications Physical CharacteristicsTemperature Switching DatabaseWeight Power SupplySwitch Features Management FeaturesCompliances SafetyStandards CE Mark EmissionsExtender Modules Warranty10G Extender Module XFP Specifications Appendix D German Instructions Eine Site Auswählen Selecting a Site GermanMontage Rack Mounting Instructions German Rack-MontageGerman Instructions Montage Rack Mounting Instructions German Appendix E Ordering Information Ordering Information Glossary-1 Glossary1000BASE-T Glossary-2 Glossary-3 Glossary-4 Glossary-5 Transmission Control Protocol/Internet Protocol TCP/IP Glossary-6Virtual LAN Vlan Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call