SMC Networks SMC8624T Compliances, FCC Class a, Industry Canada Class a, Japan Vcci Class a, Iii

Page 7

COMPLIANCES

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) cable for RJ-45 connections—Category 3 or greater for 10 Mbps connections, Category 5 for 100 Mbps connections and Category 5 or 5e for 1000 Mbps connections. Use 50/125 or 62.5/125 micron multimode fiber optic cable, or 9/125 micron single-mode cable, for SFP transceiver connections.

Warnings: 1. Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment.

2.When connecting this switch to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent elec- trical hazards.

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des Communications.

Japan VCCI Class A

iii

Image 7
Contents TigerSwitch 10/100/1000 Page TigerSwitch 10/100/1000 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Japan Vcci Class a CompliancesFCC Class a Industry Canada Class aCE Mark Declaration of Conformance for EMI and Safety EEC Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class a Safety ComplianceWarnhinweis Faseroptikanschlüsse Optische Sicherheit France and Peru only Power Cord SafetyFrance et Pérou uniquement ViiSchuko ViiiManufacturing Materials Environmental StatementPurpose End of Product Life SpanSMC8624T, SMC8648T Management Guide Related PublicationsContents Xii Making Network ConnectionsXiii AppendicesTables Xvii FiguresFigures XviiiOverview Chapter AboutManagement Options Switch Architecture10/100/1000BASE-T Ports Description of HardwareSFP Slots SMC8648T Port Status LEDs Status LEDsLED Port Status LEDsSystem Status LEDs SMC8648T System Status LEDsPower Supply Receptacles Optional Redundant Power UnitPerformance Features and BenefitsConnectivity ExpandabilityManagement About the Tigerswitch 10/100/1000 Chapter Network Planning Introduction to SwitchingCollapsed Backbone Application ExamplesNetwork Aggregation Plan Network Aggregation PlanRemote Connection with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Selecting a Site Installing the SwitchRJ-45 Connections Ethernet CablingPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingInserting an SFP Transceiver into a Slot Installing an Optional SFP Transceiver into the SwitchPower Receptacle Connecting to a Power SourceSerial Port DB-9 DTE Pin-Out Connecting to the Console PortInstalling the Switch Cabling Guidelines Connecting Network DevicesChapter Making Network Connections Twisted-Pair DevicesMaking Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesWiring Closet Connections Network Wiring ConnectionsFiber Optic SFP Devices Making LC Port Connections Maximum 1000BASE-T Gigabit Ethernet Cable Length Connectivity Rules1000BASE-T Cable Requirements Mbps Gigabit Ethernet Collision DomainMbps Ethernet Collision Domain Mbps Fast Ethernet Collision DomainCable Labeling and Connection Records Diagnosing Switch Indicators Appendix a TroubleshootingTable A-1. Troubleshooting Chart Installation Power and Cooling ProblemsIn-Band Access Twisted-Pair Cable and Pin Assignments Appendix B CablesTable B-1 /100BASE-TX MDI and MDI-X Port Pinouts 10BASE-T/100BASE-TX Pin AssignmentsFigure B-2. Straight-through Wiring Straight-Through Wiring1000BASE-T Pin Assignments Crossover WiringTable B-2 BASE-T MDI-X and MDI Port Pinouts Cable Testing for Existing Category 5 CableFiber Standards Adjusting Existing Category 5 Cabling to Run 1000BASE-TNetwork Interface Appendix C SpecificationsPhysical Characteristics Port ConfigurationPower Supply Switching Database 16K MAC address entries LEDsWeight TemperatureStandards Switch FeaturesCE Mark Emissions WarrantySafety CompliancesAppendix D Ordering Information Ordering Information Auto-Negotiation GlossaryGlossary-1 1000BASE-TGlossary-2 Glossary-3 Glossary-4 Transmission Control Protocol/Internet Protocol TCP/IP Glossary-5Virtual LAN Vlan Glossary-6 Index-1 IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call
Related manuals
Manual 78 pages 49.84 Kb