SMC Networks SMC8624T manual CE Mark Declaration of Conformance for EMI and Safety EEC

Page 8

COMPLIANCES

CE Mark Declaration of Conformance for EMI and Safety (EEC)

SMC contact for these products in Europe is:

SMC Networks Europe, Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a,

08970 - Sant Joan Despí, Barcelona, Spain.

This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied:

RFI Emission:

• Limit class A according to EN 55022:1998

 

• Limit class A for harmonic current emission according to

 

EN 61000-3-2/1995

 

• Limitation of voltage fluctuation and flicker in low-voltage supply

 

system according to EN 61000-3-3/1995

Immunity:

• Product family standard according to EN 55024:1998

 

• Electrostatic Discharge according to EN 61000-4-2:1995

 

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

 

Radio-frequency electromagnetic field according to EN 61000-4-3:1996

 

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

 

• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/

 

DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

 

• Surge immunity test according to EN 61000-4-5:1995

 

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

 

• Immunity to conducted disturbances, Induced by radio-frequency

 

fields: EN 61000-4-6:1996 (0.15 - 80 MHz with

 

1 kHz AM 80% Modulation: 3 V/m)

 

• Power frequency magnetic field immunity test according to

 

EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)

 

• Voltage dips, short interruptions and voltage variations immunity test

 

according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%

 

Reduction @500 ms, >95% Reduction @5000 ms)

LVD:

• EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)

Warning: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Les raccordeurs ne sont pas utilisé pour le systéme téléphonique!

iv

Image 8
Contents TigerSwitch 10/100/1000 Page TigerSwitch 10/100/1000 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Compliances FCC Class aIndustry Canada Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceTaiwan Bsmi Class a Australia AS/NZS 3548 1995 Class a Power Cord Safety France and Peru onlyVii France et Pérou uniquementViii SchukoEnvironmental Statement PurposeEnd of Product Life Span Manufacturing MaterialsRelated Publications SMC8624T, SMC8648T Management GuideContents Making Network Connections XiiAppendices XiiiTables Figures XviiXviii FiguresChapter About OverviewSwitch Architecture Management OptionsSFP Slots Description of Hardware10/100/1000BASE-T Ports Status LEDs SMC8648T Port Status LEDsPort Status LEDs LEDSMC8648T System Status LEDs System Status LEDsOptional Redundant Power Unit Power Supply ReceptaclesFeatures and Benefits ConnectivityExpandability PerformanceManagement About the Tigerswitch 10/100/1000 Introduction to Switching Chapter Network PlanningApplication Examples Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connection with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an Optional SFP Transceiver into the Switch Inserting an SFP Transceiver into a SlotConnecting to a Power Source Power ReceptacleConnecting to the Console Port Serial Port DB-9 DTE Pin-OutInstalling the Switch Connecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsNetwork Wiring Connections Wiring Closet ConnectionsFiber Optic SFP Devices Making LC Port Connections Connectivity Rules 1000BASE-T Cable RequirementsMbps Gigabit Ethernet Collision Domain Maximum 1000BASE-T Gigabit Ethernet Cable LengthMbps Fast Ethernet Collision Domain Mbps Ethernet Collision DomainCable Labeling and Connection Records Table A-1. Troubleshooting Chart Appendix a TroubleshootingDiagnosing Switch Indicators In-Band Access Power and Cooling ProblemsInstallation Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Table B-1 /100BASE-TX MDI and MDI-X Port PinoutsStraight-Through Wiring Figure B-2. Straight-through WiringCrossover Wiring 1000BASE-T Pin AssignmentsCable Testing for Existing Category 5 Cable Table B-2 BASE-T MDI-X and MDI Port PinoutsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsAppendix C Specifications Physical CharacteristicsPort Configuration Network InterfaceSwitching Database 16K MAC address entries LEDs WeightTemperature Power SupplySwitch Features StandardsWarranty SafetyCompliances CE Mark EmissionsAppendix D Ordering Information Ordering Information Glossary Glossary-11000BASE-T Auto-NegotiationGlossary-2 Glossary-3 Glossary-4 Virtual LAN Vlan Glossary-5Transmission Control Protocol/Internet Protocol TCP/IP Glossary-6 Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call
Related manuals
Manual 78 pages 49.84 Kb