SMC Networks SMC8624T manual Desktop or Shelf Mounting, Attaching the Adhesive Feet

Page 43

MOUNTING

3.If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, mount them in the rack, one below the other, in any order.

5.If also installing RPUs, mount them in the rack below the other devices.

Desktop or Shelf Mounting

1. Attach the four adhesive feet to the bottom of the first switch.

Figure 3-3. Attaching the Adhesive Feet

2.Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow.

3.If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, attach four adhesive feet to each one. Place each device squarely on top of the one below, in any order.

5.If also installing RPUs, place them close to the stack.

3-5

Image 43
Contents TigerSwitch 10/100/1000 Page TigerSwitch 10/100/1000 Installation Guide Trademarks Limited Warranty Limited Warranty Iii CompliancesFCC Class a EC Conformance Declaration Class aCompliances Industry Canada Class a Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany ViiViii Contents Making Network Connections Appendices Xii Overview Chapter AboutSwitching Method Switch ArchitectureManagement Options VLANs Spanning Tree ProtocolTraffic Priority Multicast Switching1000BASE-T Ports Description of HardwareSFP Slots Port and System LEDs Status LEDsSystem Status LEDs Power Supply Receptacles Optional Redundant Power UnitConnectivity Features and BenefitsPerformance Management About the Tigerswitch 10/100/1000 Chapter Network Planning Introduction to SwitchingCollapsed Backbone Sample ApplicationsCentral Wiring Closet Central Wiring ClosetRemote Connections with Fiber Cable Collapsed Backbone Using Fiber CableMaking Vlan Connections Making Vlan ConnectionsMbps Gigabit Ethernet Collision Domain Connectivity RulesSMC 2-1 Rule for Class I Repeaters Mbps Fast Ethernet Collision DomainMaximum Fast Ethernet Cable Distance SMC 3-2 Rule for Class II RepeatersSMC 5-4-3 Rule Maximum Network Diameter Using RepeatersMbps Ethernet Collision Domain Maximum Ethernet Cable DistanceApplication Notes Network Planning Selecting a Site Installing the SwitchPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingPower Receptacle Connecting to a Power SourceCabling Guidelines Connecting Network DevicesChapter Making Network Connections Twisted-Pair DevicesMaking Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesWiring Closet Connections Wiring Closet ConnectionsMaking Network Connections Diagnosing Switch Indicators Appendix a TroubleshootingPower and Cooling Problems In-Band Access InstallationAppendix B Cables SpecificationsTwisted-Pair Cable and Pin Assignments Figure B-1. RJ-45 Connector Pin NumbersRJ-45 Pin Assignments 100BASE-TX/10BASE-T Pin Assignments1000BASE-T Pin Assignments Pin MDI Signal Name MDI-X Signal NameAdjusting Existing Category 5 Cabling to Run 1000BASE-T Cable Testing for Existing Category 5 Cable1000BASE-T Cable Requirements DB-9 Port Pin Assignments Console Port Pin AssignmentsConsole Port to 9-Pin COM Port on PC Console Port to 25-Pin DTE Port on PC Cables Physical Characteristics Appendix C SpecificationsAC Input Power SupplyPower Consumption HumiditySwitch Features Standards Management FeaturesCE Mark Emissions WarrantySafety CompliancesSpecifications Appendix D Ordering Information Ordering Information Auto-Negotiation GlossaryGlossary-1 1000BASE-TGlossary-2 Glossary-3 Glossary-4 Transmission Control Protocol/Internet Protocol TCP/IP Glossary-5Virtual LAN Vlan Glossary-6 Index-1 IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call
Related manuals
Manual 80 pages 51.33 Kb