SMC Networks SMC8624T manual Wiring Closet Connections

Page 47

TWISTED-PAIR DEVICES

3.As each connection is made, the green Link LED (on the TigerSwitch) corresponding to each port will light to indicate that the connection is valid.

Wiring Closet Connections

Today, the punch-down block is an integral part of many of the newer equipment racks. It is actually part of the patch panel. Instructions for making connections in the wiring closet with this type of equipment follow.

1.Attach one end of a patch cable to an available port on the switch, and the other end to the patch panel.

2.If not already in place, attach one end of a cable segment to the back of the patch panel where the punch-down block is located, and the other end to a modular wall outlet.

3.Label the cables to simplify future troubleshooting.

SMC TigerSwitch 10/100/1000

Patch Panel

Equipment Rack (side view)

Punch-Down Block

Wall

Figure 4-2. Wiring Closet Connections

4-3

Image 47

Contents TigerSwitch 10/100/1000 Page TigerSwitch 10/100/1000 Installation Guide Trademarks Limited Warranty Limited Warranty Iii CompliancesFCC Class a EC Conformance Declaration Class aCompliances Industry Canada Class a Underwriters Laboratories Compliance Statement Safety ComplianceWarnhinweis Faseroptikanschlüsse Optische Sicherheit Wichtige Sicherheitshinweise Germany ViiViii Contents Making Network Connections Appendices Xii Overview Chapter AboutManagement Options Switch ArchitectureSwitching Method VLANs Spanning Tree ProtocolTraffic Priority Multicast SwitchingSFP Slots Description of Hardware1000BASE-T Ports Port and System LEDs Status LEDsSystem Status LEDs Power Supply Receptacles Optional Redundant Power UnitConnectivity Features and BenefitsPerformance Management About the Tigerswitch 10/100/1000 Chapter Network Planning Introduction to SwitchingCollapsed Backbone Sample ApplicationsCentral Wiring Closet Central Wiring ClosetRemote Connections with Fiber Cable Collapsed Backbone Using Fiber CableMaking Vlan Connections Making Vlan ConnectionsMbps Gigabit Ethernet Collision Domain Connectivity RulesSMC 2-1 Rule for Class I Repeaters Mbps Fast Ethernet Collision DomainMaximum Fast Ethernet Cable Distance SMC 3-2 Rule for Class II RepeatersSMC 5-4-3 Rule Maximum Network Diameter Using RepeatersMbps Ethernet Collision Domain Maximum Ethernet Cable DistanceApplication Notes Network Planning Selecting a Site Installing the SwitchOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingPower Receptacle Connecting to a Power SourceCabling Guidelines Connecting Network DevicesChapter Making Network Connections Twisted-Pair DevicesMaking Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesWiring Closet Connections Wiring Closet ConnectionsMaking Network Connections Power and Cooling Problems Appendix a TroubleshootingDiagnosing Switch Indicators In-Band Access InstallationAppendix B Cables SpecificationsTwisted-Pair Cable and Pin Assignments Figure B-1. RJ-45 Connector Pin NumbersRJ-45 Pin Assignments 100BASE-TX/10BASE-T Pin Assignments1000BASE-T Pin Assignments Pin MDI Signal Name MDI-X Signal Name1000BASE-T Cable Requirements Cable Testing for Existing Category 5 CableAdjusting Existing Category 5 Cabling to Run 1000BASE-T Console Port to 9-Pin COM Port on PC Console Port Pin AssignmentsDB-9 Port Pin Assignments Console Port to 25-Pin DTE Port on PC Cables Physical Characteristics Appendix C SpecificationsAC Input Power SupplyPower Consumption HumiditySwitch Features Standards Management FeaturesCE Mark Emissions WarrantySafety CompliancesSpecifications Appendix D Ordering Information Ordering Information Auto-Negotiation GlossaryGlossary-1 1000BASE-TGlossary-2 Glossary-3 Glossary-4 Virtual LAN Vlan Glossary-5Transmission Control Protocol/Internet Protocol TCP/IP Glossary-6 Index-1 IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call

Related manuals

Manual 80 pages 51.33 Kb