SMC Networks SMC6826MPE manual Europe

Page 12

COMPLIANCES

•Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die Stromversorgung des Geräts kann nur durch Herausziehen des Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.

•Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen (Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter SELV-Bedingungen betrieben werden.

Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:

Schweiz	Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalten.
Europe	Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung)
	sein und die Aufschrift <HAR> oder <BASEC> tragen.
	Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).

Warnings and Cautionary Messages

Warning: This product does not contain any serviceable user parts.

Warning: Installation and removal of the unit must be carried out by qualified personnel only.

Warning: When connecting this device to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards.

Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

Caution: All interconnecting LAN cables and devices receiving PoE (Power over Ethernet) power from a switch must be contained within the same building.

Caution: Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment.

Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!

Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards.

vi

Image 12

Contents TigerStack III 10/100 Page TigerStack III 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty Compliances FCC Class aIndustry Canada Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC AC/DC Line to Line ±1 kV, AC/DC Line to Earth ±2 kVSafety Compliance Power Cord SafetyAustralia AS/NZS 3548 1995 Class a IiiPower Cord Set Schuko Europe Environmental Statement PurposeVii Audience Related PublicationsViii Table of Contents Making Network Connections Appendices Tables XiiFigures XiiiXiv FiguresChapter About OverviewSwitch Architecture Power-over-Ethernet CapabilityNetwork Management Options Description of Hardware 10/100BASE-T Ports1000BASE-T/SFP Ports Port and System Status LED Indicators Port Status LED IndicatorsLED System LED Indicators System Status LED IndicatorsStack Master Button Stack Master ButtonMode PoE/Link Button Optional Stacking TransceiverFeatures and Benefits Power Supply SocketsConnectivity Expandability PerformanceManagement Introduction to Switching Chapter Network PlanningApplication Examples Supplying PoECollapsed Backbone Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Network Planning Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsEquipment Checklist Package ContentsOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Montage Rack Mounting Instructions German Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an SFP Transceiver Installing an SFP TransceiverStacking Switches Installing a Stacking TransceiverConnecting Switches in a Stack Connecting Switches in a StackStacking Switches Connecting to a Power Source Power SocketConnecting to the Console Port Wiring Map for Serial CableSerial Cable Wiring Stop bit-One Data bits-8 Flow control-none Connecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Power-over-Ethernet Connections Connecting to PCs, Servers, Hubs and Switches Cabling GuidelinesNetwork Wiring Connections Network Wiring Connections Fiber Optic Devices Connectivity Rules Making Fiber Port Connections1000BASE-T Cable Requirements Mbps Gigabit Ethernet Collision DomainMaximum 1000BASE-T Gigabit Ethernet Cable Length Maximum 1000BASE-SX Gigabit Ethernet Cable LengthsCable Labeling and Connection Records Mbps Fast Ethernet Collision DomainMbps Ethernet Collision Domain Making Network Connections Appendix a Troubleshooting Diagnosing Switch IndicatorsTable A-1 Troubleshooting Chart Power and Cooling Problems Diagnosing Power Problems with the LED IndicatorsTable A-2 Power/RPU LED Indicators Installation In-Band AccessStack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI-X and MDI Port PinoutsStraight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover Wiring1000BASE-T Pin Assignments Cable Testing for Existing Category 5 Cable Table B-2 1000BASE-T MDI-X and MDI Port PinoutsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsCables Appendix C Specifications Physical CharacteristicsSwitch Features Management Features StandardsIn-Band Management Out-of-Band ManagementSafety CompliancesEmissions ImmunityTable D-1 TigerStack III 10/100 Products and Accessories Appendix D Ordering InformationOrdering Information Glossary Glossary-11000BASE-T Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call