SMC Networks SMC6826MPE manual Power Cord Set

Page 10

COMPLIANCES

•The socket outlet must be near to the unit and easily accessible. You can only remove power from the unit by disconnecting the power cord from the outlet.

•This unit operates under SELV (Safety Extra Low Voltage) conditions according to

IEC 60950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT† supplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary con- nection point labelled Neutral, connected directly to earth (ground).

†Impédance à la terre

Important! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following:

Power Cord Set

	U.S.A. and	The cord set must be UL-approved and CSA certified.
	Canada
	Canada	The minimum specifications for the flexible cord are:
		The minimum specifications for the flexible cord are:
		- No. 18 AWG - not longer than 2 meters, or 16 AWG.
		- Type SV or SJ
		- 3-conductor
		The cord set must have a rated current capacity of at least 10 A

		The attachment plug must be an earth-grounding type with NEMA 5-15P
		(15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
	Denmark	The supply plug must comply with Section 107-2-D1, Standard DK2-1a
		or DK2-5a.
	Switzerland	The supply plug must comply with SEV/ASE 1011.

	U.K.	The supply plug must comply with BS1363 (3-pin 13 A) and be fitted with
		a 5 A fuse which complies with BS1362.
		The mains cord must be <HAR> or <BASEC> marked and be of type
		HO3VVF3GO.75 (minimum).
	Europe	The supply plug must comply with CEE7/7 (“SCHUKO”).

		The mains cord must be <HAR> or <BASEC> marked and be of type
		HO3VVF3GO.75 (minimum).
		IEC-320 receptacle.

Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch:

AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un personnel qualifié.

•Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il n'y a pas de connexion de mise à la terre (mise à la masse).

•Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes internationales de sécurité.

iv

Image 10

Contents TigerStack III 10/100 Page TigerStack III 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty Industry Canada Class a CompliancesFCC Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC AC/DC Line to Line ±1 kV, AC/DC Line to Earth ±2 kVAustralia AS/NZS 3548 1995 Class a Safety CompliancePower Cord Safety IiiPower Cord Set Schuko Europe Purpose Environmental StatementVii Related Publications AudienceViii Table of Contents Making Network Connections Appendices Tables XiiFigures XiiiXiv FiguresChapter About OverviewSwitch Architecture Power-over-Ethernet CapabilityNetwork Management Options 10/100BASE-T Ports Description of Hardware1000BASE-T/SFP Ports Port and System Status LED Indicators Port Status LED IndicatorsLED System LED Indicators System Status LED IndicatorsStack Master Button Stack Master ButtonMode PoE/Link Button Optional Stacking TransceiverPower Supply Sockets Features and BenefitsConnectivity Expandability PerformanceManagement Introduction to Switching Chapter Network PlanningApplication Examples Supplying PoECollapsed Backbone Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Network Planning Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Montage Rack Mounting Instructions German Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an SFP Transceiver Installing an SFP TransceiverStacking Switches Installing a Stacking TransceiverConnecting Switches in a Stack Connecting Switches in a StackStacking Switches Connecting to a Power Source Power SocketWiring Map for Serial Cable Connecting to the Console PortSerial Cable Wiring Stop bit-One Data bits-8 Flow control-none Chapter Making Network Connections Connecting Network DevicesTwisted-Pair Devices Power-over-Ethernet Connections Connecting to PCs, Servers, Hubs and Switches Cabling GuidelinesNetwork Wiring Connections Network Wiring Connections Fiber Optic Devices Connectivity Rules Making Fiber Port ConnectionsMaximum 1000BASE-T Gigabit Ethernet Cable Length 1000BASE-T Cable RequirementsMbps Gigabit Ethernet Collision Domain Maximum 1000BASE-SX Gigabit Ethernet Cable LengthsMbps Fast Ethernet Collision Domain Cable Labeling and Connection RecordsMbps Ethernet Collision Domain Making Network Connections Diagnosing Switch Indicators Appendix a TroubleshootingTable A-1 Troubleshooting Chart Diagnosing Power Problems with the LED Indicators Power and Cooling ProblemsTable A-2 Power/RPU LED Indicators Installation In-Band AccessStack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI-X and MDI Port PinoutsStraight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover Wiring1000BASE-T Pin Assignments Cable Testing for Existing Category 5 Cable Table B-2 1000BASE-T MDI-X and MDI Port PinoutsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsCables Appendix C Specifications Physical CharacteristicsSwitch Features In-Band Management Management FeaturesStandards Out-of-Band ManagementEmissions SafetyCompliances ImmunityTable D-1 TigerStack III 10/100 Products and Accessories Appendix D Ordering InformationOrdering Information Glossary-1 Glossary1000BASE-T Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call