SMC Networks SMC6826MPE manual Rack Mounting

Page 44

INSTALLING THE SWITCH

Mounting

This switch can be mounted in a standard 19-inch equipment rack or on a desktop or shelf. Mounting instructions for each type of site follow.

Rack Mounting

Before rack mounting the switch, pay particular attention to the following factors:

•Temperature: Since the temperature within a rack assembly may be higher than the ambient room temperature, check that the rack-environment temperature is within the specified operating temperature range. (See page C-2.)

•Mechanical Loading: Do not place any equipment on top of a rack-mounted unit.

•Circuit Overloading: Be sure that the supply circuit to the rack assembly is not overloaded.

•Grounding: Rack-mounted equipment should be properly grounded. Particular attention should be given to supply connections other than direct connections to the mains.

To rack-mount devices:

1.Attach the brackets to the device using the screws provided in the Bracket Mounting Kit.

3-4

Image 44

Contents TigerStack III 10/100 Page TigerStack III 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty Compliances FCC Class aIndustry Canada Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC AC/DC Line to Line ±1 kV, AC/DC Line to Earth ±2 kVSafety Compliance Power Cord SafetyAustralia AS/NZS 3548 1995 Class a IiiPower Cord Set Schuko Europe Vii Environmental StatementPurpose Viii AudienceRelated Publications Table of Contents Making Network Connections Appendices Tables XiiFigures XiiiXiv FiguresChapter About OverviewSwitch Architecture Power-over-Ethernet CapabilityNetwork Management Options 1000BASE-T/SFP Ports Description of Hardware10/100BASE-T Ports Port and System Status LED Indicators Port Status LED IndicatorsLED System LED Indicators System Status LED IndicatorsStack Master Button Stack Master ButtonMode PoE/Link Button Optional Stacking TransceiverConnectivity Features and BenefitsPower Supply Sockets Expandability PerformanceManagement Introduction to Switching Chapter Network PlanningApplication Examples Supplying PoECollapsed Backbone Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Network Planning Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack MountingAttaching the Brackets Montage Rack Mounting Instructions German Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an SFP Transceiver Installing an SFP TransceiverStacking Switches Installing a Stacking TransceiverConnecting Switches in a Stack Connecting Switches in a StackStacking Switches Connecting to a Power Source Power SocketSerial Cable Wiring Connecting to the Console PortWiring Map for Serial Cable Stop bit-One Data bits-8 Flow control-none Twisted-Pair Devices Connecting Network DevicesChapter Making Network Connections Power-over-Ethernet Connections Connecting to PCs, Servers, Hubs and Switches Cabling GuidelinesNetwork Wiring Connections Network Wiring Connections Fiber Optic Devices Connectivity Rules Making Fiber Port Connections1000BASE-T Cable Requirements Mbps Gigabit Ethernet Collision DomainMaximum 1000BASE-T Gigabit Ethernet Cable Length Maximum 1000BASE-SX Gigabit Ethernet Cable LengthsMbps Ethernet Collision Domain Cable Labeling and Connection RecordsMbps Fast Ethernet Collision Domain Making Network Connections Table A-1 Troubleshooting Chart Appendix a TroubleshootingDiagnosing Switch Indicators Table A-2 Power/RPU LED Indicators Power and Cooling ProblemsDiagnosing Power Problems with the LED Indicators Installation In-Band AccessStack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI-X and MDI Port PinoutsStraight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover Wiring1000BASE-T Pin Assignments Cable Testing for Existing Category 5 Cable Table B-2 1000BASE-T MDI-X and MDI Port PinoutsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsCables Appendix C Specifications Physical CharacteristicsSwitch Features Management Features StandardsIn-Band Management Out-of-Band ManagementSafety CompliancesEmissions ImmunityTable D-1 TigerStack III 10/100 Products and Accessories Appendix D Ordering InformationOrdering Information 1000BASE-T GlossaryGlossary-1 Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call