SMC Networks SMC6826MPE manual Connecting to a Power Source, Power Socket

Page 52

INSTALLING THE SWITCH

Connecting to a Power Source

To connect a switch to a power source:

1.Insert the power cable plug directly into the AC socket located at the back of the switch.

100-240V~ 50/60Hz 8.0-2.0A

Figure 3-8 Power Socket

2.Plug the other end of the cable into a grounded, 3-pin socket, AC power source.

Note: For international use, you may need to change the AC line cord. You must use a line cord set that has been approved for the socket type in your country.

3.Check the front-panel LED indicators as the device is powered on to be sure the PWR LED is lit. If not, check that the power cable is correctly plugged in.

4.If you have purchased a Redundant Power Supply, connect it to the device and to an AC power source now, following the instructions included with the package.

3-12

Image 52

Contents TigerStack III 10/100 Page TigerStack III 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty Compliances FCC Class aIndustry Canada Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC AC/DC Line to Line ±1 kV, AC/DC Line to Earth ±2 kVSafety Compliance Power Cord SafetyAustralia AS/NZS 3548 1995 Class a IiiPower Cord Set Schuko Europe Purpose Environmental StatementVii Related Publications AudienceViii Table of Contents Making Network Connections Appendices Tables XiiFigures XiiiXiv FiguresChapter About OverviewSwitch Architecture Power-over-Ethernet CapabilityNetwork Management Options 10/100BASE-T Ports Description of Hardware1000BASE-T/SFP Ports Port and System Status LED Indicators Port Status LED IndicatorsLED System LED Indicators System Status LED IndicatorsStack Master Button Stack Master ButtonMode PoE/Link Button Optional Stacking TransceiverPower Supply Sockets Features and BenefitsConnectivity Expandability PerformanceManagement Introduction to Switching Chapter Network PlanningApplication Examples Supplying PoECollapsed Backbone Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Network Planning Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Montage Rack Mounting Instructions German Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an SFP Transceiver Installing an SFP TransceiverStacking Switches Installing a Stacking TransceiverConnecting Switches in a Stack Connecting Switches in a StackStacking Switches Connecting to a Power Source Power SocketWiring Map for Serial Cable Connecting to the Console PortSerial Cable Wiring Stop bit-One Data bits-8 Flow control-none Chapter Making Network Connections Connecting Network DevicesTwisted-Pair Devices Power-over-Ethernet Connections Connecting to PCs, Servers, Hubs and Switches Cabling GuidelinesNetwork Wiring Connections Network Wiring Connections Fiber Optic Devices Connectivity Rules Making Fiber Port Connections1000BASE-T Cable Requirements Mbps Gigabit Ethernet Collision DomainMaximum 1000BASE-T Gigabit Ethernet Cable Length Maximum 1000BASE-SX Gigabit Ethernet Cable LengthsMbps Fast Ethernet Collision Domain Cable Labeling and Connection RecordsMbps Ethernet Collision Domain Making Network Connections Diagnosing Switch Indicators Appendix a TroubleshootingTable A-1 Troubleshooting Chart Diagnosing Power Problems with the LED Indicators Power and Cooling ProblemsTable A-2 Power/RPU LED Indicators Installation In-Band AccessStack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI-X and MDI Port PinoutsStraight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover Wiring1000BASE-T Pin Assignments Cable Testing for Existing Category 5 Cable Table B-2 1000BASE-T MDI-X and MDI Port PinoutsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsCables Appendix C Specifications Physical CharacteristicsSwitch Features Management Features StandardsIn-Band Management Out-of-Band ManagementSafety CompliancesEmissions ImmunityTable D-1 TigerStack III 10/100 Products and Accessories Appendix D Ordering InformationOrdering Information Glossary-1 Glossary1000BASE-T Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call