Seagate ST9160823AS, ST980813ASG manual Formatted capacity, Default logical geometry, LBA mode

Page 11

Table 1:

Drive specifications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ST9200420ASG

ST9160823AS

 

 

ST980813AS

Drive specification

ST9200420AS

ST9160823ASG

ST9120823AS

ST9100821AS

ST980813ASG

 

 

 

 

 

 

Load/Unload (L/UL) cycles

 

 

 

 

 

25°C, 50% relative humidity

600,000 software-controlled power on/off cycles

 

 

 

20,000 hard power on/off cycles

 

32°C, 80% relative humidity

600,000 software-controlled power on/off cycles

 

5°C, 80% relative humidity

20,000 hard power on/off cycles

 

5°C, 20% relative humidity

 

 

 

 

 

60°C, 20% relative humidity

 

 

 

 

 

 

 

 

 

 

 

Supports Hotplug operation per SATA II

Yes

 

 

 

 

specification

 

 

 

 

 

 

 

 

 

 

 

 

 

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby modes will not contribute to battery power consumption.

2.2Formatted capacity

Model

Formatted capacity*

Guaranteed sectors

Bytes per sector

 

 

 

 

ST9200420AS and ST9200420ASG

200 Gbytes

390,721,968

512

 

 

 

 

ST9160823AS and ST9160823ASG

160 Gbytes

312,581,808

512

 

 

 

 

ST9120823AS

120 Gbytes

234,441,648

512

 

 

 

 

ST9100821AS

100 Gbytes

195,371,568

512

 

 

 

 

ST980813AS and ST980813ASG

80 Gbytes

156,301,488

512

 

 

 

 

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

2.2.1LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,where n is the number of guaranteed sectors as defined above.

See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48- bit addressing support of drives with capacities over 137 Gbytes.

2.3Default logical geometry

Cylinders

Read/write heads

Sectors per track

 

 

 

16,383

16

63

 

 

 

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,where n is the number of guaranteed sectors as defined above.

Momentus 7200.2 SATA Product Manual, Rev. E

5

Image 11
Contents Momentus 7200.2 Sata Page Contents Momentus 7200.2 Sata Product Manual, Rev. E List of Figures Page Introduction About the Serial ATA Sata interface Specification summary table Drive specificationsWill display the warranty information for your drive Cylinders Read/write heads Sectors per track 16,383 Default logical geometryLBA mode Formatted capacityRecording and interface technology Physical characteristicsPhysical organization Typical seek times msec Read Write Seek timeStart/stop times Typical seek timesPower specifications Voltage tolerance Typical current profileConducted noise Idle mode Power-management modesPower management modes Active modeEnvironmental specifications Vibration ShockOperating shock Nonoperating shockRadio frequency environments AcousticsElectromagnetic immunity Drive level acousticsAgency certification Free Fall Protection featureSafety certification ReliabilityFCC verification Korean RRLAustralian C-Tick N176 Corrosive environment超出 Environmental protectionPage Momentus 7200.2 Sata Product Manual, Rev. E Handling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveDrive mounting Drive dimensionsMomentus 7200.2 Sata Product Manual, Rev. E Segment Pin Function Definition Serial ATA connector pin definitionsSerial ATA Sata interface P10 Ground 2nd mate P11 Reserved Pin Function DefinitionCommand name Command code in hex ATA-standard commands Supported ATA commandsATA-standard security commands Command name Command code in hexATA-standard power-management commands Word Description Value Identify Device commandXxxxH Bit Word Description if bit is set to Bit WordSet Features command values Set Features commandCode in features register A.R.T. command 3 S.M.A.R.T. commandsA.R.T. commands Momentus 7200.2 Sata Product Manual, Rev. E Technical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index ITE Sata Momentus 7200.2 Sata Product Manual, Rev. E Page Seagate Technology LLC