Seagate ST980813ASG, ST9200420ASG, ST9160823ASG, ST9120823AS Drive mounting, Drive dimensions

Page 27

3.4Drive mounting

You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mount- ing the drive:

•Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

•Use only M3 UNC mounting screws.

•Do not overtighten the mounting screws (maximum torque: 4.0 inch-lb).

•Four (4) threads (0.080 inches) minimum screw engagement recommended.

.138 +/- .015 (3.505 +/- .381)

.528 +/- .015

(13.411 +/- .381)

2.750 +/- .010

(69.85 +/- .254)

inches

(mm)

3.957 +/- .010

(100.5 +/- .254) 0.490 +/- .010

(12.446 +/- .254)

0.680 +/- .010

(17.27 +/- .254)

Breather Hole Do not cover or seal.

Recommended case temp. measurement location

3.567

(90.602)

.551

(13.99)

.374 +/- .0078

(9.5 +/- .2)

2X .118 Both sides

2X M3 X 0.5-6H Mounting holes Both sides

.12 min. full thread

	3.567
	(90.60)	4X M3 X 0.5-6H
.551		4X M3 X 0.5-6H
.551		Mounting holes
(13.99)		.10 min. full thread
		2.430
		(61.722)
		.160
		(4.06)

Figure 4. Drive dimensions

Momentus 7200.2 SATA Product Manual, Rev. E

21

Image 27

Contents Momentus 7200.2 Sata Page Contents Momentus 7200.2 Sata Product Manual, Rev. E List of Figures Page Introduction About the Serial ATA Sata interface Specification summary table Drive specificationsWill display the warranty information for your drive Cylinders Read/write heads Sectors per track 16,383 Default logical geometryLBA mode Formatted capacityPhysical characteristics Physical organizationRecording and interface technology Typical seek times msec Read Write Seek timeStart/stop times Typical seek timesPower specifications Typical current profile Conducted noiseVoltage tolerance Idle mode Power-management modesPower management modes Active modeEnvironmental specifications Vibration ShockOperating shock Nonoperating shockRadio frequency environments AcousticsElectromagnetic immunity Drive level acousticsAgency certification Free Fall Protection featureSafety certification ReliabilityKorean RRL Australian C-Tick N176FCC verification Corrosive environment超出 Environmental protectionPage Momentus 7200.2 Sata Product Manual, Rev. E Handling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveDrive mounting Drive dimensionsMomentus 7200.2 Sata Product Manual, Rev. E Serial ATA connector pin definitions Serial ATA Sata interfaceSegment Pin Function Definition P10 Ground 2nd mate P11 Reserved Pin Function DefinitionCommand name Command code in hex ATA-standard commands Supported ATA commandsCommand name Command code in hex ATA-standard power-management commandsATA-standard security commands Word Description Value Identify Device commandXxxxH Bit Word Description if bit is set to Bit WordSet Features command values Set Features command3 S.M.A.R.T. commands A.R.T. commandsCode in features register A.R.T. command Momentus 7200.2 Sata Product Manual, Rev. E Technical Support Seagate Technology support servicesInternet Presales SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index ITE Sata Momentus 7200.2 Sata Product Manual, Rev. E Page Seagate Technology LLC