Seagate ST9120822AS, ST980811AS manual Pin Function Definition, P10 Ground 2nd mate P11 Reserved

Page 28

	Table 7:	Serial ATA connector pin definitions

	Segment	Pin	Function	Definition

		P1	V33	3.3V power
		P2	V33	3.3V power
		P3	V33	3.3V power, pre-charge, 2nd mate
		P4	Ground	1st mate

		P5	Ground	2nd mate

		P6	Ground	2nd mate

		P7	V5	5V power, pre-charge, 2nd mate

		P8	V5	5V power
	Power
	Power	P9	V5	5V power
		P9	V5	5V power

		P10	Ground	2nd mate

		P11	Reserved	The pin corresponding to P11 in the backplane receptacle connector is also reserved
				The corresponding pin to be mated with P11 in the power cable receptacle connector
				shall always be grounded

		P12	Ground	1st mate.

		P13	V12	12V power, pre-charge, 2nd mate
		P14	V12	12V power
		P15	V12	12V power

Notes:

1.All pins are in a single row, with a 1.27 mm (0.050”) pitch.

2.The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are:

•the ground pins P4 and P12.

•the pre-charge power pins and the other ground pins.

•the signal pins and the rest of the power pins.

3.There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration.

4.All used voltage pins (Vx) must be terminated.

22	Momentus 5400.3 SATA Product Manual, Rev. D

Image 28

Contents Momentus 5400.3 Sata Page Contents Momentus 5400.3 Sata Product Manual, Rev. D List of Figures Page Introduction About the Serial ATA interface Drive specifications Specification summary tableDrive specifications Default logical geometry LBA modeFormatted capacity Cylinders Read/write heads Sectors per track 16,383Physical characteristics Drive specificationPhysical organization Recording and interface technologySeek time Start/stop timesTypical seek times Typical seek times msec Read WritePower specifications Typical current profile Deferred spinupConducted noise Voltage toleranceEnvironmental specifications Temperature gradient Wet bulb temperatureHumidity Relative humidity AltitudeShock Operating shockNonoperating shock VibrationAcoustics Electromagnetic immunityDrive level acoustics Radio frequency environmentsSafety certification Measurement type SpecificationReliability Agency certificationAustralian C-Tick N176 Korean RRLFCC verification Corrosive environment Environmental protectionEuropean Union Restriction of Hazardous Substances RoHS Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectors Mounting dimensions-top, side and end view Drive mountingMomentus 5400.3 Sata Product Manual, Rev. D Serial ATA connector pin definitions SignalSerial ATA Sata interface Segment Pin Function DefinitionPin Function Definition P10 Ground 2nd mate P11 ReservedSupported ATA commands Command name Command code in hex ATA-standard commandsCommand name Command code in hex ATA-standard security commandsMomentus 5400.3 Sata Product Manual, Rev. D Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordSet Features command Set Features command valuesA.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Seagate Technology support services InternetPresales Support Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index ITE Sata Momentus 5400.3 Sata Product Manual, Rev. D Page Seagate Technology LLC