Seagate ST936701SS, ST973401SS manual Signal characteristics

Page 67

9.4.7Power

The drive receives power (+5 volts and +12 volts) through the SAS device connector.

Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power sup- ply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Current to the drive through the long power pins may be limited by the system to reduce inrush current to the drive during hot plugging.

9.5Signal characteristics

This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 23 for signal type and signal name information.

9.5.1Ready LED Out

The Ready LED Out signal is driven by the drive as indicated in Table 24.

Table 24: Ready LED Out conditions

Normal command activity

 

LED status

 

 

 

Ready LED Meaning bit mode page 19h

0

 

1

 

 

 

 

Spun down and no activity

Off

 

Off

 

 

 

 

Spun down and activity (command executing)

On

 

On

 

 

 

 

Spun up and no activity

On

 

Off

 

 

 

 

Spun up and activity (command executing)

Off

 

On

 

 

 

 

Spinning up or down

 

Blinks steadily

 

(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)

 

 

 

Format in progress, each cylinder change

 

Toggles on/off

 

 

 

 

The Ready LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +3.3 volt supply through an appropriate current limiting resistor. The LED and the current limiting resis- tor are external to the drive. See Table 25 for the output characteristics of the LED drive signals.

Table 25:

LED drive signal

 

 

 

 

 

State

 

Test condition

Output voltage

 

 

 

 

LED off, high

 

0 V ≤ VOH ≤ 3.6 V

-100 µA < IOH < 100 µA

 

 

 

 

LED on, low

 

IOL = 15 mA

0 ≤ VOL ≤ 0.225 V

 

 

 

 

9.5.2Differential signals

The drive SAS differential signals comply with the intra-enclosure (internal connector) requirements of the SAS standard.

Savvio SAS Product Manual, Rev. D

61

Page 66 Page 68
Image 67
Page 66 Page 68
Contents ST973401SS ST936701SS Savvio SASPage Contents Interface requirements Defect and error managementInstallation Seagate Technology support servicesList of Figures Page Savvio family disc drive ScopeSavvio SAS Product Manual, Rev. D Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean MIC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickSAS Interface Manual Reference documentsSavvio SAS Product Manual, Rev. D General description Media description Standard featuresPerformance Programmable drive capacity Factory-installed accessoriesReliability Formatted capacitiesUser-installed accessories Factory-installed optionsAccess time Performance characteristicsInternal drive characteristics Seek performance characteristicsGeneral performance characteristics Format command execution time for 512-byte sectors minutesPrefetch/multi-segmented cache control Start/stop timeCache operation Caching write data Prefetch operation Savvio SAS Product Manual, Rev. D Unrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsPerformance impact Hot plugging the drive4 S.M.A.R.T Controlling S.M.A.R.TThermal monitor Reporting controlDetermining rate Predictive failuresImplementation Temperature Log Page 0Dh Parameter Code DescriptionDrive Self Test DST DST failure definitionShort test Function Code 001b State of the drive prior to testingInvoking DST Short and extended testsShipping Product warrantyLog page entries AbortProduct repair and return information ST973401SS DC power requirements Physical/electrical specificationsAC power requirements DC power requirementsGeneral DC power requirement notes ST936701SS DC power requirementsST936701SS Gbit mode Amps +5V +12V Power sequencingConducted noise immunity Current profilesTypical ST973401SS drive +12V current profile Typical ST936701SS drive +12V current profile ST973401SS in 3 Gbit operation Power dissipationST973401SS in 1.5 Gbit operation ST936701SS in 1.5 Gbit operation ST936701SS in 3 Gbit operationEnvironmental limits TemperatureRelative humidity Shock and vibration Effective altitude sea levelShock Recommended mounting Package size Packaged/product weight Drop heightVibration Air cleanlinessCorrosive environment Acoustics Mounting configuration dimensions Mechanical specificationsSavvio SAS Product Manual, Rev. D Drive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Drive orientation InstallationAir flow CoolingGrounding Drive mountingSavvio SAS Product Manual, Rev. D Interface requirements SAS featuresDual port support Commands supported by Savvio SAS family drive Scsi commands supportedCommand name Command code Supported Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Bytes Data hex Mode Sense dataInquiry data Savvio inquiry dataPage DEF CHG Savvio SAS Product Manual, Rev. D Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features Supported Feature or conditionSAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionSAS pin descriptions Pin Signal name Signal typeSAS transmitters and receivers Signal characteristics Receive eye mask General interface characteristicsCharacteristic Units Gbps Eye masks Eye masks overviewReveive tolerance eye mask Jitter tolerance masksFrequency in kHz Peak-toSinusoidal JitterSignal characteristica Units Gbps Transmitter signal characteristicsGbps m, n Deterministic jitterq Receiver signal characteristicsSignal characteristic Units Gbps Maximum allowable jitterImpedance requirements Sheet 1 Impedance specificationsReceiver jitter tolerance Compliant jitter test pattern CjtpatImpedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Tctf ISI loss example at 1.5 Gbps Receiver characteristicsSavvio SAS Product Manual, Rev. D Technical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Numerics IndexPage SAS See also cooling
Related manuals
Manual 1 pages 21.51 Kb

ST936701SS, ST973401SS specifications

The Seagate ST936701SS and ST973401SS are high-performance enterprise hard drives designed for optimal data storage solutions in demanding environments. Both models belong to Seagate's Savvio series, which is renowned for its reliability and efficiency. These drives are tailored for critical applications such as database management, data warehousing, and online transaction processing.

The ST936701SS comes with a storage capacity of 36.4 GB, while the ST973401SS offers a larger capacity of 73.4 GB. This variance allows users to choose the drive that best suits their storage needs without compromising performance. Both drives utilize a 2.5-inch form factor, making them compact and suitable for high-density storage configurations.

A key feature of these drives is their impressive rotational speed of 10,000 RPM, which enhances data access times and improves overall system responsiveness. This speed allows for reduced latency and faster data transfer rates, critical for applications that require quick retrieval of large datasets.

In terms of technology, these drives utilize the Serial Attached SCSI (SAS) interface, which is favored in enterprise settings for its reliability and speed. SAS provides better performance than traditional SATA drives, particularly when dealing with high workloads, as it supports multiple concurrent connections and higher data throughput.

The ST936701SS and ST973401SS are also equipped with advanced features such as Seagate's Native Command Queuing (NCQ), which optimizes the order in which read and write commands are executed. This results in improved performance under multi-tasking conditions, essential for enterprise servers managing multiple requests simultaneously.

Additionally, both drives incorporate features aimed at enhancing data integrity and reliability. They support End-to-End Data Protection and are designed to endure the rigors of continuous operation, with MTBF (Mean Time Between Failures) ratings that bolster their reputation for durability.

Energy efficiency is another notable characteristic, as both drives are designed to reduce power consumption without sacrificing performance. This is particularly important in enterprise environments where power management contributes to lower operational costs.

In conclusion, the Seagate ST936701SS and ST973401SS drives are robust, reliable storage solutions tailored for enterprise applications. With their high performance, advanced technology features, and capacity options, they provide organizations with the scalability and efficiency required in today’s data-driven landscape. Whether it's for critical data management tasks or high-access applications, these drives stand out as a solid choice for any enterprise storage strategy.
Top Page Image Contents