Seagate ST95005620AS manual Ite

Page 40

H

handling		19
Handling precautions 19
heads	5
Height	3
height	6
humidity		4

I

I/O data-transfer rate 3,						6
Identify		24
Identify Device				24
Identify Device command						26
Idle	8,	25
Idle and Standby timers						11
Idle Immediate				25
Idle mode			4,	11
Idle mode power					8
IEC950		15
Information Technology Equipment (ITE) 15
Initialize Device Parameters 24
Input noise ripple					10
Interface			6
interface			22
Interleave			6
Internal data transfer rate						3
Internal data-transfer rate						6
ITE	15

K

Korean RRL 15

L

latency 3 LBA mode 5 Length 3 length 6 Load/Unload 14 logical geometry 5

M

master/slave 2 Max Address 24 maximum temperature 12 Microcode 24 mounting 21

mounting screws 13 mounting the drive 19

N

NAND Flash memory 5 noise 10

nominal power 7 Nonoperating shock 13 Nonoperating vibration 13 Nonrecoverable read errors 4 nonrecoverable read errors 14

O

Operating shock 13

Operating vibration 13

P

Physical characteristics 6 Physical organization 6 Physical read/write heads 3 point-to-point 2, 20 Power consumption 8 power dissipation 8 power management 11 power on/off cycles 14 Power specifications 8 Power-management modes 11 Power-on to Ready 7 Power-on to ready 3 precautions 19, 21 programmable power management 11

Q

quick reference 3

R

Radiated RF immunity 14
Radio and television interference 15
radio frequency (RF)			14
random track location			8
Read Buffer	24
Read DMA	24
Read DMA Extended			24
Read DMA without Retries				24
read errors	4, 14
Read Long with Retries 24
Read Long without Retries				24
Read Multiple 24
Read Multiple Extended 24
Read Native Max Address				24
Read Native Max Address Extended						24
Read Sectors 24
Read Sectors Extended 24
Read Sectors without Retries					24
Read Verify Sectors			24
Read Verify Sectors Extended					24
Read Verify Sectors without Retries						24
Read/write heads		5
Read/write power		4

34	Momentus XT Product Manual, Rev. A

Image 40

Contents Momentus XT ST95005620AS ST93205620AS ST92505610ASRevision history Revision DateContents Momentus XT Product Manual, Rev. a List of Figures Page Introduction Standard modelsAbout the Serial ATA interface Drive specifications Specification summary tableYes requires Comreset from host after a hotplug event Default logical geometry LBA modeSolid State Hybrid feature Specifics of the Solid State Hybrid FeaturePhysical characteristics Drive specificationPhysical organization Recording and interface technologySeek time Start/stop timesTypical seek times Typical seek times ms ReadPower specifications Typical current profile Typical +5V only startup and operation current profileConducted noise Voltage tolerancePower-management modes Power management modesActive mode Idle modeEnvironmental specifications Acoustics Electromagnetic immunity ReliabilityTest for Prominent Discrete Tones PDTs Radio frequency environmentsAgency certification Page European Union Restriction of Hazardous Substances RoHS Environmental protectionChina Restriction of Hazardous Substances RoHS Directive Corrosive environment Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions-top, side and end view Drive mountingSerial ATA Sata interface Hot-Plug compatibilitySerial ATA device plug connector pin definitions Serial ATA connector pin definitionsSignal Pin Function DefinitionSupported ATA commands ATA-standard commands names Command code in hexATA-standard security commands Identify Device command Word Description ValueXx07H Description if bit is set to Bit Set Features command Set Features command valuesA.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Warranty Support Direct.seagate.com Spp.seagate.com Seagate Technology support servicesWeb Technical Support Warranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Presales SupportIndex ITE TPI Momentus XT Product Manual, Rev. a Page Seagate Technology LLC