Seagate ST160LT011 - 9ZVG4D manual Configuring and mounting the drive, Configuring the drive

Page 24

4.0Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

4.1Handling and static-discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis- charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

•Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s exposure to ESD.

•Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

•Handle the drive only by its edges or frame.

•The drive is fragile—handle it with care. Do not press down on the drive top cover.

•Always rest the drive on a padded, antistatic surface until you mount it in the computer.

•Do not touch the connector pins or the printed circuit board.

•Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

4.2Configuring the drive

Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationships. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This means both drives behave as if they are Device 0 (master) devices.

Serial ATA drives are designed for easy installation. It is normally not necessary to set any jumpers on this drive for proper operation. If the host system does not support SATA 3Gb/s operation, place a jumper on pins 1 and 2 to limit the drive to 1.5Gb/s operation.

3.0 Gbits per second operation

Limit data transfer rate to 1.5 Gbits per second

Jumper block

SATA power connector

SATA interface connector

Figure 2. Serial ATA connectors

18

Momentus Thin Product Manual, Rev. C Gen-2

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Momentus Thin ST model #Revision history Revision DateContents Momentus Thin Product Manual, Rev. C Gen-2 List of Figures Page Seagate Technology support services Seagate Online Support and ServicesIntroduction About the Serial ATA interface Drive specifications Specification summary tableWarranty information for your drive Default logical geometry LBA modeFormatted capacity Physical organizationPhysical characteristics Recording and interface technologySeek time Typical seek timesPower specifications Start/stop timesMomentus Thin Product Manual, Rev. C Gen-2 Typical current profile Deferred spinupConducted noise Voltage tolerancePower-management modes Power management modesActive mode Idle modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationDrive A-weighted Sound Power Levels SWL, BA AcousticsElectromagnetic immunity Test for Prominent Discrete Tones PDTsSafety certification ReliabilityAgency certification Electromagnetic compatibilityAustralian C-Tick N176 FCC verificationEnvironmental protection Corrosive environmentEuropean Union Restriction of Hazardous Substances RoHS China Restriction of Hazardous Substances RoHS DirectiveConfiguring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectors Drive mountingTop cover stiffness/deflection Measurements shown in Figures 4 and 5 are in inches Momentus Thin Product Manual, Rev. C Gen-2 About Fips PurposeLevel 2 security Momentus Thin Product Manual, Rev. C Gen-2 Serial ATA connector pin definitions SignalSerial ATA Sata interface Segment Pin Function DefinitionPin Function Definition P10 Ground 2nd mate P11 ReservedSupported ATA commands Command name Command code in hex ATA-standard commandsCommand name Command code in hex ATA-standard power-management commandsATA-standard security commands Identify Device command Word Description ValueXx7FH Description if bit is set to Bit Word Bit Word Set Features command Set Features command values3 S.M.A.R.T. commands A.R.T. commandsCode in features register A.R.T. command Momentus Thin Product Manual, Rev. C Gen-2 Index ITE TPI Momentus Thin Product Manual, Rev. C Gen-2 Page Seagate Technology LLC

ST250LT014 - 9YK14C, ST160LT011 - 9ZVG4D, ST320LT007 - 9ZV142, ST160LT014 - 9YK14D, ST160LT007 - 9ZV14D specifications

The Seagate ST160LT014, ST320LT014, ST320LT011, ST160LT007, and ST250LT009 are part of Seagate’s esteemed line of mobile hard drives, known for their reliability and performance in various computing environments. These drives are particularly designed for use in laptops, external storage solutions, and other portable computing devices, delivering a balance of storage capacity, speed, and ruggedness.

The ST160LT014, for instance, provides a storage capacity of 160GB, making it suitable for users who require efficient and dependable storage for essential files while keeping weight and power consumption minimal. It measures 2.5 inches, making it an ideal fit for most laptop configurations. With a spindle speed of 5400 RPM, this model offers a good performance level for everyday tasks.

The ST320LT014 offers a larger capacity of 320GB. This model boasts not only the same 5400 RPM spindle speed but also utilizes SATA interface technology to ensure faster data transfer rates. This versatility allows for an improved user experience, especially for those working with larger files such as multimedia content.

With the ST320LT011, Seagate has upgraded the design, introducing an innovative error correction feature that enhances the drive’s reliability and data integrity. This model maintains the 320GB capacity while offering improved power management features, making it a more energy-efficient option compared to its predecessors.

On the other hand, the ST160LT007 advocates for a more compact and efficient solution with its 160GB storage size. This hard drive, like its counterparts, is engineered to operate under various conditions, ensuring that users can depend on its performance in both business and personal applications.

The ST250LT009 provides a middle ground with a 250GB capacity. This model is lauded for its balance between capacity and performance, and it is particularly favorable for users who require a reasonable amount of storage without compromising speed or energy efficiency.

All of these models incorporate advanced technologies such as Seagate's QuietStep technology, which minimizes noise and vibration during operation, providing a tranquil computing experience. Additionally, their designs often include adaptive power management features that help prolong battery life in laptops, making them suitable for mobile professionals on the go.

In conclusion, the Seagate ST160LT014, ST320LT014, ST320LT011, ST160LT007, and ST250LT009 represent a range of options tailored to meet diverse storage needs while ensuring reliability, efficiency, and performance in portable computing.
Top Page Image Contents