Seagate ST31000640AS, ST31000340AS manual Reliability, Agency certification, Safety certification

Page 22

2.11Reliability

2.11.1Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)

The product shall achieve an Annualized Failure Rate (AFR) of 0.34% (MTBF of 0.7 million hours) when oper- ated in an environment of ambient air temperatures of 25°C. Operation at temperatures outside the specifica- tions in Section 2.8 may increase the product AFR (decrease MTBF). AFR and MTBF are population statistics that are not relevant to individual units.

AFR and MTBF specifications are based on the following assumptions for desktop personal computer environ- ments:

•2400 power-on-hours per year.

•10,000 average motor start/stop cycles per year.

•Operations at nominal voltages.

•Temperatures outside the specifications in Section 2.8 may reduce the product reliability.

•Normal I/O duty cycle for desktop personal computers. Operation at excessive I/O duty cycle may degrade product reliability.

The desktop personal computer environment of power-on-hours, temperature, and I/O duty cycle affect the product AFR and MTBF. The AFR and MTBF will be degraded if used in an enterprise application

Nonrecoverable read errors

1 per 1014 bits read, max

Annualized Failure Rate (AFR)

0.34% (nominal power, 25°C ambient temperature)

 

 

Contact start-stop cycles

50,000 cycles

 

(at nominal voltage and temperature, with 60 cycles per hour and a 50% duty cycle)

 

 

Warranty

5 years on distribution units.

 

To determine the warranty for a specific drive, use a web browser to access the

 

following web page: www.seagate.com/support/service/

 

From this page, click on the “Verify Your Warranty” link. You will be asked to provide

 

the drive serial number, model number (or part number) and country of purchase.

 

The system will display the warranty information for your drive.

 

 

Preventive maintenance

None required.

 

 

2.12Agency certification

2.12.1Safety certification

The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950.

2.12.2Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec- tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024.

Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products.

16

Barracuda 7200.11 Serial ATA Product Manual, Rev. C

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Barracuda 7200.11 Serial ATA Revision history Revision Date Sheets affected or commentsContents Barracuda 7200.11 Serial ATA Product Manual, Rev. C List of Figures Typical 5V startup and operation current profilePage Introduction About the Serial ATA interface Drive specifications Drive specifications summary for 1000 and 750 Gbyte models Barracuda 7200.11 Serial ATA Product Manual, Rev. C Drive specifications summary for 500 Gbyte models Barracuda 7200.11 Serial ATA Product Manual, Rev. C Formatted capacity Default logical geometryLBA mode Recording and interface technologyStart/stop times Physical characteristicsSeek time Typical seek times msec Read WritePower specifications Typical 5V startup and operation current profile Typical 12V startup and operation current profileIdle mode Power-management modesActive mode Sleep modeEnvironmental specifications Nonoperating vibration VibrationOperating vibration 1000 GB, 750 GB and 500 GB modelsFluid Dynamic Bearing FDB motor acoustics AcousticsElectromagnetic immunity Test for Prominent Discrete Tones PDTsAgency certification Safety certificationReliability Electromagnetic compatibilityAustralian C-Tick N176 Korean RRLFCC verification Environmental protection Corrosive environment超出Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions Drive mountingBarracuda 7200.11 Serial ATA Product Manual, Rev. C Serial ATA Sata interface Hot-Plug compatibilitySignal Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions Pin Function DefinitionSupported ATA commands Supported ATA commandsCommand name Command code in hex F3H Command name Command code in hex Write Sectors Extended 34H Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordSet Features command Set Features command valuesA.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Presales Support Seagate Technology support servicesInternet Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index Page Sata Barracuda 7200.11 Serial ATA Product Manual, Rev. C Page Seagate Technology LLC
Related manuals
Manual 48 pages 57.3 Kb

ST3500820AS, ST3500320AS, ST3500620AS, ST31000640AS, ST31000340AS specifications

Seagate has long been a prominent player in the hard drive industry, and its line of SATA drives, including the ST3640330AS, ST3750330AS, ST3750630AS, ST31000340AS, and ST31000640AS, showcases a blend of performance, reliability, and advanced technology. These drives cater to various user needs, from consumer desktops to enterprise applications.

The ST3640330AS and ST3750330AS models are designed with a 7200 RPM spinning speed, ensuring fast data throughput for gaming, multimedia, and everyday computing tasks. With a SATA interface and compatibility with the latest systems, these drives are ideal for users seeking efficient storage solutions. The ST3640330AS provides 640 GB of storage, while the ST3750330AS boasts a generous 750 GB capacity, offering ample space for large files and applications.

Moving to the ST3750630AS, this model continues the trend of high performance, offering 750 GB of storage but enhanced with Seagate’s advanced error-correcting technology. It also features an updated cache architecture that optimizes read and write speeds while minimizing latency. This drive is particularly beneficial for users who require reliable backups and quick access to data.

The ST31000340AS and ST31000640AS are both part of Seagate’s 1 TB series and are engineered for durability and longevity. The ST31000340AS features traditional SATA technology, providing users with a balance between cost and performance. On the other hand, the ST31000640AS integrates improved power management features that result in lower energy consumption without compromising performance. This makes it a suitable choice for environmentally-conscious consumers or businesses looking to reduce operational costs.

All models feature Seagate's proprietary technologies such as SoftSonic drives, which result in quieter operation, and advanced power management capabilities that extend the lifespan of the hard drives. They are equipped with robust error recovery and data security features, ensuring data integrity and protecting against data loss.

Overall, the Seagate ST3640330AS, ST3750330AS, ST3750630AS, ST31000340AS, and ST31000640AS drives represent a comprehensive range of storage solutions that combine capacity, speed, and cost-effectiveness, making them a popular choice for a variety of users, from casual consumers to demanding enterprise environments.
Top Page Image Contents