Seagate 7200-RPM manual Shock, Operating shock, Nonoperating shock, Vibration, Operating vibration

Page 20

3.10.6Shock

All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis.

Note. Additional shock protection is provided by the Free Fall Protection feature on ST9750423ASG, ST9750420ASG, ST9640423ASG and ST9500423ASG models. See Section 3.13.1 for additional information about this feature.

3.10.6.1Operating shock

These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 350 Gs based on half-sine shock pulses of 2ms. Shocks should not be repeated more than one time per axis.

3.10.6.2Nonoperating shock

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse of 2 ms duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 1000 Gs based on a nonrepetitive half-sine shock pulse of 1 ms duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 1000 Gs based on a nonrepetitive half-sine shock pulse of 0.5 ms duration.

3.10.7Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis.

3.10.7.1Operating vibration

The maximum vibration levels that the drive may experience while meeting the performance standards speci- fied in this document are specified below.

5–200 Hz	2.0	Gs (0 to peak). Max displacement may apply below 10 Hz.

200–500 Hz	1.0	Gs (0 to peak).

3.10.7.2Nonoperating vibration

The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degrada- tion in performance when subsequently put into operation are specified below.

5–500 Hz:

5 Gs (0 to peak). Max displacement may apply below 22 Hz.

14	Momentus Product Manual, Rev. B

Image 20

Contents Momentus Standard models Free-fall sensor modelsRevision history Revision Date Sheets affected or commentsContents Momentus Product Manual, Rev. B List of Figures Page Seagate Technology support services Seagate Online Support and ServicesIntroduction Standard models Free Fall Protection modelsAbout the Serial ATA interface Drive specifications for 750, 640 and 500 GB models Drive specificationsSpecification summary table Altitude, nonoperating Default logical geometry LBA modeFormatted capacity Physical organizationRecording and interface technology Physical characteristicsDrive specification Seek time Start/stop timesTypical seek times Typical seek times ms ReadPower specifications Typical current profile Conducted noise Voltage tolerancePower-management modes Power management modesActive mode Idle modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationDrive A-weighted Sound Power Levels SWL, BA AcousticsElectromagnetic immunity Test for Prominent Discrete Tones PDTsFree Fall Protection feature Safety certificationReliability Agency certificationFCC verification Korean RRLAustralian C-Tick N176 Environmental protection Corrosive environmentEuropean Union Restriction of Hazardous Substances RoHS China Restriction of Hazardous Substances RoHS DirectiveConfiguring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions-top, side and end view Drive mountingSerial ATA Sata interface Hot-Plug compatibilitySerial ATA device plug connector pin definitions Serial ATA connector pin definitionsSignal Pin Function DefinitionSupported ATA commands Command name Command code in hex ATA-standard commandsCommand name Command code in hex ATA-standard security commandsIdentify Device command Word Description ValueXxxxH Fffeh Description if bit is set to Bit Set Features command Set Features command valuesCode in features register A.R.T. command 3 S.M.A.R.T. commandsA.R.T. commands Momentus Product Manual, Rev. B Index ITE TPI Momentus Product Manual, Rev. B Page Seagate Technology LLC