Seagate ST3120828AS installation instructions Easiest way to install your drive, What you need

Barracuda 7200.7 Serial ATA Installation Guide

ST3160228AS, ST3160828AS, ST3120228AS, ST3120828AS,

ST380219AS, ST380819AS, ST340212AS, and ST340812AS

Serial ATA (SATA) Interface Disc Drives

Publication Number: 100383102, Rev. A, August 2005

Serial ATA interface disc drives are designed for easy installation. It is nor- mally not necessary to set any jumpers, terminators, or other settings on this drive for proper operation.

With a Serial ATA interface, each disc drive has its own cable that connects directly to a Serial ATA host adapter or a Serial ATA port on your mother- board. Unlike Parallel ATA, there is no master-slave relationship between drives that use a Serial ATA interface.

You can use a Serial ATA drive in the same system with Parallel ATA drives as long as both interfaces are supported on the motherboard or with a host adapter. This makes it easy to add Serial ATA capability to your existing system without removing existing Parallel ATA disc drives.

The easiest way to install your drive

To successfully install and obtain the maximum capacity from the drive, use DiscWizard‰ 2003 disc drive installation software utility. This utility is available exclusively from Seagate. You can download this free disc drive installation software from our web site at www.seagate.com/support or run the program directly from your web browser. In either case, you should run DiscWizard before you install your drive.

Note. Older versions of DiscWizard do not recognize Serial ATA model numbers. Make sure that you use DiscWizard 2003 or later when installing a Barracuda‚ 7200.7 Serial ATA disc drive.

To run DiscWizard:

Follow the instructions on the download page at www.seagate.com to cre- ate a diskette and complete the installation.

If you cannot run DiscWizard, follow the instructions on this installation sheet to install and configure your drive.

What you need

•A Phillips screwdriver and four 6-32 UNC drive mounting screws.

•A Serial ATA interface cable (sold separately). Maximum length is 39 inches (1 meter).

•A Serial ATA-compatible power cable or adapter (sold separately).

•A version of Windows with FAT32 or NTFS file system.

•A system with a Serial ATA connector on it, or a Serial ATA host adapter and available PCI slot in which to install the adapter.

Refer to your computer system documentation to see if your system sup- ports Serial ATA on the motherboard and to locate the Serial ATA connec- tor. If your system does not have a Serial ATA connector on the motherboard, you must purchase a Serial ATA host adapter that is compat- ible with your computer and operating system and install it with the appro- priate device driver according to the host adapter manufacturer’s installation instructions.

Note. See www.seagate.com/support/disc/sata/ for a list of companies that sell Serial ATA components including host adapters, cables, and power adapters.

Handling precautions/electrostatic discharge protection

•Disc drives are fragile. Do not drop or jar the drive. Handle the drive only by the edges or frame. Keep the drive in the protective SeaShell‰ con- tainer until you are ready to install it to minimize handling damage.

•Drive electronics are extremely sensitive to static electricity. While installing the drive, wear a wrist strap and cable connected to ground.

•Turn off the power to the host system during installation.

•Do not disassemble the drive. Doing so voids the warranty. See the Warranty information on page 2.

•Do not apply pressure or attach labels to the circuit board or to the top of the drive.

Breather filter hole precaution

Breather Hole

Do not cover

or seal.

Caution. Do not cover, seal, or insert any object into this hole.

Note. If this hole is covered, sealed, or penetrated by any object, the drive reliability may be compromised and could lead to permanent damage—doing so voids the warranty.

Drive characteristics

	ST3160228AS	ST3160828AS	ST3120228AS
Formatted capacity *	160 Gbytes	160 Gbytes	120 Gbytes
Total # of sectors* *	312,581,808	312,581,808	234,441,648
Cache size	2 Mbytes	8 Mbytes	2 Mbytes

	ST3120828AS	ST380219AS	ST380819AS
Formatted capacity	120 Gbytes	80 Gbytes	80 Gbytes
Total # of sectors*	234,441,648	156,301,488	156,301,488
Cache size	8 Mbytes	2 Mbytes	8 Mbytes

	ST340212AS	ST340812AS
Formatted capacity	40 Gbytes	40 Gbytes
Total # of sectors*	78,165,360	78,165,360
Cache size	2 Mbytes	8 Mbytes

*One Gbyte equals one billion bytes. **One sector equals 512 bytes.

Attaching cables and mounting the drive

1.Attach one end of the drive interface cable to the Serial ATA interface connector on your computer’s motherboard or Serial ATA host adapter (see your computer manual for connector locations). Host adapter configuration is shown below.

Computer	SATA
	drive
motherboard
	SATA
	cable
	Jumper block
	(factory use only)
	SATA
	Interface cable
SATA	power
host adapter
	adapter
	cable
	Note: The drive is inverted in this
	illustration to show the connectors.

Note. Serial ATA connectors are keyed to ensure correct orientation.

2.Attach the interface and power cables to the drive.

3.Secure the drive using four 6-32 UNC mounting screws in either the side-mounting or bottom-mounting holes. Insert the screws no more than 0.20 inches (5.08 mm) into the bottom-mounting holes and no more than 0.14 inches (3.55 mm) into the side-mounting holes.

Note. Do not overtighten the screws or use metric screws. This may dam- age the drive.