Samsung HT-410HD Selecting Resolution, Set the resolution switch to 576p480p, Cooling Fan

Page 9

1p~40p(410HD)-GB 7/27/04 4:58 PM Page 18

Connectingthe Video Out to TV

Selecting Resolution

You can adjust the resolution switch to set the DVI and component (PR, PB, Y) output resolution to 576p(480p)/720p/1080i.

Connectingthe FM and AM Antennas

If AM reception is poor, connect an outdoor AM antenna(not supplied).

Example: If the TV supports resolution up to 576p(480p)

1 Set the resolution switch to 576p(480p).

• A 576p(480p) video signal is output through the DVI and component outputs (PR, PB, Y).

Caution

•

If you connect the DVI and Component outputs (PR, PB, Y) at the same time, Component output resolution changes

 

automatically to the designated DVI resolution.

 

Note

•

If copy protection is in place, output resolution is automatically converted to 576p(480p) when you play the

 

DVD, even if you set the resolution to 720p or 1080i.

DCDi (Directional Correlational Deinterlacing) Function

Converts the interlace signal to progressive to prevent flickering and to remove distortion or noise on the edge of screen.

Press and hold DCDi button on the remote control for over 3 seconds.

FM Antenna (supplied)

FM antenna connection

1.Connect the FM antenna supplied to the FM 75Ω COAXIAL terminal as a temporary mea- sure.

2.Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or other rigid surface.

AM Loop Antenna (supplied)

Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna.

AM antenna connection

1.Connect the AM loop antenna supplied

to the AM and terminals.

2.If reception is poor, connect an outdoor single vinyl-covered wire to the AM ter- minal. (Keep the AM loop antenna con- nected).

CONNECTIONS

• Each time the button is pressed, the selection alternates between

DCDi ON and DCDi OFF.

Cooling Fan

The cooling fan dissipates the heat generated inside the unit so that the unit can be operated

normally. The cooling fan is activated automatically to supply cool air to the unit.

 

 

Please observe the following cautions for your safety.

 

• Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the unit could rise

 

and may damage it.

 

• Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are covered with a

 

newspaper or cloth, heat may build up inside the unit and fire may result.)

15

16

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Digital Home Cinema System Class 1 Laser Product Safety Warnings PrecautionsContents Do not use the following types of disc Playable DiscsDisc Recording Format Copy ProtectionDescription Replace the battery Remove the battery Insert two 1.5V AAARange of Operation of the Remote Control Insert Remote BatteriesConnecting the Speakers Method 3 When you connect to DVI Video Method1 When you connect to Video OutWhat is DVI Digital Visual Interface? ScartSet the resolution switch to 576p480p Selecting ResolutionFM antenna connection AM antenna connectionPress AUX on the remote control to select AUX 1 or AUX Connecting External ComponentsPress the Power button to turn on the TV Power supplyPress TV/VIDEO button to select Video mode Press DVD button to select DVD/CD modePress OPEN/CLOSE button to open the disc tray Load a discs Disc PlaybackPress OPEN/CLOSE button to close the disc tray Disc terminologyPress the Remain button MP3 -CD PlaybackPress Each time the Remain button is pressedJpeg File Playback Jpeg Press Slide Mode buttonPress To skip to the next slide Press Cursor , , , buttons during playbackDivX Playback Fast/Slow Playback Displaying Disc InformationPress Info button Press Slow buttonRepeat Playback Skipping Scenes/SongsBriefly press Press Repeat buttonPress Info button twice Repeat Playback Angle FunctionPress Enter DesiredZoom Function Press Enter buttonPress EZ View button Press the numeric buttons 1Press Info buttonPress Cursor , 3 buttons to move to Chapter display Press Cursor Press the numeric Buttons to selectUsing the Title Menu Using Disc MenuStop mode Press Menu button Press Menu button to exit the setup screen‘Setup’ and then Stop modePress Cursor Button to move toAdjusting the TV Aspect Ratio Screen Size Letterbox43 Pan&Scan Enter the password Then press Enter button Setting Parental Controls Rating LevelSetting the Password Setting the Wallpaper Jpeg DVD VCD Setting the Wallpaper To Change the WallpaperPress Open Close to close the disc tray DVD Playback Mode AV Sync SetupPress the Menu button Press Cursor , buttons Press Return button to return to the previous levelSetting the Test Tone Setting the Speaker ModeStop mode, press Menu button Press Test Tone buttonSetting up the Speaker Delay Time Setting the Delay TimePress Cursor button Then press EnterSetting the Audio Quality Press Sound Edit button and then press CursorEnter button Sound Field DSP/EQ Function Press Cursor , to adjust the ‘DRC’Stop mode, press Menu buttonDolby Pro Logic II Mode Press PL II Mode buttonDolby Pro Logic II Effect Listening to Radio Presetting StationsPTY Program Type indication and PTY-SEARCH function About RDS broadcastingConvenient Functions To confirm the sleep timer setting, press Sleep buttonPress Sleep button Press Dimmer buttonPress the Mode button to make the TV TV Brand Code ListIndicator on the remote control flash When operating a TV with the remote controlBefore Calling for Service Handling discs SpecificationsDisc Storage Handling and Storing DiscsMemo
Top Page Image Contents