Seagate ST31000640SS, ST3750630SS Standard features, Media description, Performance, Reliability

Page 12

3.1Standard features

Barracuda ES.2 SAS drives have the following standard features:

•Perpendicular recording technology

•1.5 / 3 Gbit Serial Attached SCSI (SAS) interface

•Integrated dual port SAS controller

•Support for SAS expanders and fanout adapters

•Downloadable firmware using the SAS interface

•128 - deep task set (queue)

•Supports up to 32 initiators

•Jumperless configuration.

•User-selectable logical block size (512, 520, 524, or 528 bytes per logical block)

•Programmable logical block reallocation scheme

•Flawed logical block reallocation at format time

•Programmable auto write and read reallocation

•Reallocation of defects on command (Post Format)

•ECC maximum burst correction length of 400 bits

•No preventive maintenance or adjustments required

•Dedicated head landing zone

•Embedded servo design

•Automatic shipping lock

•Self diagnostics performed when power is applied to the drive

•Zone bit recording (ZBR)

•Vertical, horizontal, or top down mounting

•Dynamic spindle brake

•16 Mbyte data buffer (see Section 4.5).

•Drive Self Test (DST)

•Background Media Scan (BGMS)

•Power Save

3.2Media description

The media used on the drive has an aluminum substrate coated with a thin film magnetic material, overcoated with a proprietary protective layer for improved durability and environmental protection.

3.3Performance

•Firmware-controlled multisegmented cache designed to dynamically adjust segments for enhanced system performance.

•300 Mbytes/sec maximum instantaneous data transfers.

•7,200 RPM spindle. Average latency = 4.16 msec

•Command queuing of up to 128 commands

•Background processing of queue

•Supports start and stop commands (spindle stops spinning)

•Adaptive seek velocity; improved seek performance

3.4Reliability

•Annualized Failure Rate (AFR) of 0.73%

•Mean Time Between Failures (MTBF) of 1,200,000 hours

•Self-Monitoring Analysis and Reporting Technology (S.M.A.R.T.)

•5-year warranty

8

Barracuda ES.2 SAS Product Manual, Rev. E

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Barracuda ES.2 SAS ST31000640SS ST3750630SS ST3500620SSPage Contents Defect and error management InstallationSeagate Technology support services Interface requirementsScope Barracuda ES.2 SAS Product Manual, Rev. E Standards, compliance and reference documents StandardsElectromagnetic compatibility Electromagnetic susceptibilityCompliance Reference documents Barracuda ES.2 SAS Product Manual, Rev. E General description Barracuda ES.2 drive illustrationStandard features Media descriptionPerformance ReliabilityFactory-installed options Formatted capacitiesProgrammable drive capacity Barracuda ES.2 SAS Product Manual, Rev. E Performance characteristics Internal drive characteristicsAccess time Seek performanceFormat command execution time minutes General performance characteristicsStart/stop time Prefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Reliability specifications Error ratesRecoverable Errors Unrecoverable ErrorsReliability and service Seek errorsInterface errors Preventive maintenance4 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Reporting controlTemperature Log Page 0Dh Predictive failuresThermal monitor State of the drive prior to testing DST failure definitionImplementation Invoking DSTProduct warranty Short test Function Code 001bExtended test Function Code 010b Log page entriesShipping Product repair and return informationBarracuda ES.2 SAS Product Manual, Rev. E Physical/electrical specifications AC power requirementsDC power requirements ST31000640SS DC power requirementsST3750630SS DC power requirements ST3500620SS DC power requirementsGeneral DC power requirement notes Power sequencingConducted noise immunity Current profilesTypical ST31000640SS drive +5V and +12V current profiles Power dissipation Typical ST3500620SS drive +5V and +12V current profilesBarracuda ES.2 SAS Product Manual, Rev. E Temperature a. Operating Environmental limitsRelative humidity Effective altitude sea level a. OperatingShock and vibration ShockPackage size Packaged/product weight Drop height Air cleanliness Vibration a. Operating-normalAcoustics Corrosive environmentX表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。 Mechanical specifications Physical dimensionsDefect and error management Drive internal defects/errorsDrive error recovery procedures 108.29 SAS system errors Background Media ScanMedia Pre-Scan Deferred Auto-Reallocation Idle Read After WriteInstallation Drive orientationCooling Air flowDrive mounting GroundingBarracuda ES.2 SAS Product Manual, Rev. E SAS features Interface requirementsDual port support Scsi commands supported Commands supported by Barracuda ES.2 SAS family drivesCommands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Mode Sense data Inquiry dataPage 2.1 ST31000640SS Mode Sense data Mode Pages2.2 ST3750630SS Mode Sense data 2.3 ST3500620SS Mode Sense data Miscellaneous operating features and conditions Miscellaneous featuresMiscellaneous status SAS physical interface Datum B Physical characteristics Connector requirementsElectrical description Pin descriptionsSAS pin descriptions Signal characteristics PowerSAS transmitters and receivers Ready LED OutLED drive signal Differential signalsGeneral interface characteristics Eye masks Eye masks overviewReceive eye mask Jitter tolerance masksPeak-to SinusoidalJitter Frequency in kHzTransmitter signal characteristics Receiver signal characteristics Maximum allowable jitterImpedance specifications Receiver jitter toleranceCompliant jitter test pattern Cjtpat Impedance requirements Sheet 1Transmitter characteristics Impedance requirements Sheet 2Electrical TxRx connections = -5, 437dB Shows the zero-length test load Receiver characteristics Barracuda ES.2 SAS Product Manual, Rev. E Seagate Technology support services InternetPresales Support Technical SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index Page SAS See also cooling Page Seagate Technology LLC

ST31000640SS, ST3500620SS, ST3750630SS specifications

Seagate has been a leading name in the storage industry for decades, and its range of enterprise-class hard drives showcases advanced technologies and robust performance. The Seagate ST3750630SS, ST3500620SS, and ST31000640SS are three notable models that cater to the demands of data centers and enterprises. Each model is designed with specific features that enhance reliability and efficiency, making them suitable for various applications.

The Seagate ST3750630SS is a 750GB 15K RPM Serial Attached SCSI (SAS) drive. It boasts a high-performance architecture that allows for fast data transfer rates, making it ideal for high-load environments such as transaction processing and video streaming. This drive features an MTBF of 1.6 million hours, ensuring minimal downtime due to failures. It also employs advanced error recovery and data protection mechanisms, including error correction codes (ECC), to maintain data integrity.

Meanwhile, the ST3500620SS offers a capacity of 500GB with a spinning speed of 15K RPM as well. This drive utilizes the SAS interface, providing users with improved bandwidth and connectivity compared to traditional SATA drives. The ST3500620SS is designed with a focus on high availability, featuring a robust design that supports multiple workloads simultaneously. Its quick access times enhance overall system performance, making it a preferred choice for high-performance computing applications.

The ST31000640SS is another enterprise-class offering, delivering 1TB of storage capacity. Like its counterparts, this drive operates at 15K RPM and utilizes the SAS interface, facilitating fast data processing and retrieval. It also incorporates a dual-port design which allows for redundancy and failover capabilities. This feature is critical in enterprise environments where data access and uptime are paramount. The drive's design is optimized for durability and longevity, best suited for environments that require 24/7 operation.

All three Seagate drives feature advanced technologies such as dual-stage actuators and thermal write technology, ensuring improved read and write performance, along with reduced power consumption. Additionally, they are built to endure the rigors of enterprise workloads, including heavy I/O operations and high access demands.

In summary, the Seagate ST3750630SS, ST3500620SS, and ST31000640SS are exemplary models that reflect the company’s commitment to quality and performance in enterprise storage solutions. With their high speeds, reliability, and extensive features, these drives are well-equipped to meet the challenges of modern data-driven environments.
Top Page Image Contents