Seagate ST3750630SS, ST31000640SS manual Start/stop time, Format command execution time minutes

Page 16

4.2.2Format command execution time (minutes)

 

ST31000640SS

ST3750630SS

ST3500620SS

Maximum (with verify)

400

300

200

Maximum (without verify)

200

150

100

Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the request for a Status Byte Transfer to the Initiator (excluding connect/disconnect).

4.2.3

General performance characteristics

 

Sustainable disk transfer rate*:

 

Minimum

56 Mbytes/sec

Maximum

116 Mbytes/sec

SAS Interface maximum instantaneous transfer rate

300 Mbytes/sec* per port

 

 

(dual port = 600 Mbytes/sec*)

Logical block sizes

 

Default is 512-byte data blocks

 

Sector sizes variable to 512, 520, 524, and 528 kbytes.

 

Read/write consecutive sectors on a track

Yes

Flaw reallocation performance impact (for flaws reallocated at format time using

Negligible

the spare sectors per sparing zone reallocation scheme.)

 

*Assumes no errors and no relocated logical blocks. Rate measured from the start of the first logical block transfer to or from the host.

4.3Start/stop time

The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has been applied.

If the drive receives a NOTIFY (ENABLE SPINUP) primitive through either port and has not received a START STOP UNIT command with the START bit equal to 0, the drive becomes ready for normal operations within 20 seconds (excluding the error recovery procedure).

If the drive receives a START STOP UNIT command with the START bit equal to 0 before receiving a NOTIFY (ENABLE SPINUP) primitive, the drive waits for a START STOP UNIT command with the START bit equal to 1. After receiving a START STOP UNIT command with the START bit equal to 1, the drive waits for a NOTIFY (ENABLE SPINUP) primitive. After receiving a NOTIFY (ENABLE SPINUP) primitive through either port, the drive becomes ready for normal operations within 20 seconds (excluding the error recovery procedure).

If the drive receives a START STOP UNIT command with the START bit and IMMED bit equal to 1 and does not receive a NOTIFY (ENABLE SPINUP) primitive within 5 seconds, the drive fails the START STOP UNIT command.

The START STOP UNIT command may be used to command the drive to stop the spindle. Stop time is 20 sec- onds (maximum) from removal of DC power.

There is no power control switch on the drive.

12

Barracuda ES.2 SAS Product Manual, Rev. E

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Barracuda ES.2 SAS ST31000640SS ST3750630SS ST3500620SSPage Contents Defect and error management InstallationSeagate Technology support services Interface requirementsScope Barracuda ES.2 SAS Product Manual, Rev. E Standards, compliance and reference documents StandardsElectromagnetic compatibility Electromagnetic susceptibilityCompliance Reference documents Barracuda ES.2 SAS Product Manual, Rev. E General description Barracuda ES.2 drive illustrationStandard features Media descriptionPerformance ReliabilityFormatted capacities Factory-installed optionsProgrammable drive capacity Barracuda ES.2 SAS Product Manual, Rev. E Performance characteristics Internal drive characteristicsAccess time Seek performanceGeneral performance characteristics Format command execution time minutesStart/stop time Cache operation Prefetch/multi-segmented cache controlCaching write data Prefetch operation Reliability specifications Error ratesRecoverable Errors Unrecoverable ErrorsReliability and service Seek errorsInterface errors Preventive maintenance4 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Reporting controlPredictive failures Temperature Log Page 0DhThermal monitor State of the drive prior to testing DST failure definitionImplementation Invoking DSTProduct warranty Short test Function Code 001bExtended test Function Code 010b Log page entriesShipping Product repair and return informationBarracuda ES.2 SAS Product Manual, Rev. E Physical/electrical specifications AC power requirementsDC power requirements ST31000640SS DC power requirementsST3750630SS DC power requirements ST3500620SS DC power requirementsGeneral DC power requirement notes Power sequencingConducted noise immunity Current profilesTypical ST31000640SS drive +5V and +12V current profiles Power dissipation Typical ST3500620SS drive +5V and +12V current profilesBarracuda ES.2 SAS Product Manual, Rev. E Temperature a. Operating Environmental limitsRelative humidity Effective altitude sea level a. OperatingShock and vibration ShockPackage size Packaged/product weight Drop height Air cleanliness Vibration a. Operating-normalAcoustics Corrosive environmentX表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。 Mechanical specifications Physical dimensionsDrive internal defects/errors Defect and error managementDrive error recovery procedures 108.29 Background Media Scan SAS system errorsMedia Pre-Scan Deferred Auto-Reallocation Idle Read After WriteInstallation Drive orientationCooling Air flowDrive mounting GroundingBarracuda ES.2 SAS Product Manual, Rev. E SAS features Interface requirementsDual port support Scsi commands supported Commands supported by Barracuda ES.2 SAS family drivesCommands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Mode Sense data Inquiry dataPage 2.1 ST31000640SS Mode Sense data Mode Pages2.2 ST3750630SS Mode Sense data 2.3 ST3500620SS Mode Sense data Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Physical characteristics Connector requirementsPin descriptions Electrical descriptionSAS pin descriptions Signal characteristics PowerSAS transmitters and receivers Ready LED OutLED drive signal Differential signalsGeneral interface characteristics Eye masks Eye masks overviewReceive eye mask Jitter tolerance masksPeak-to SinusoidalJitter Frequency in kHzTransmitter signal characteristics Receiver signal characteristics Maximum allowable jitterImpedance specifications Receiver jitter toleranceCompliant jitter test pattern Cjtpat Impedance requirements Sheet 1Impedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5, 437dB Shows the zero-length test load Receiver characteristics Barracuda ES.2 SAS Product Manual, Rev. E Seagate Technology support services InternetPresales Support Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index Page SAS See also cooling Page Seagate Technology LLC

ST31000640SS, ST3500620SS, ST3750630SS specifications

Seagate has been a leading name in the storage industry for decades, and its range of enterprise-class hard drives showcases advanced technologies and robust performance. The Seagate ST3750630SS, ST3500620SS, and ST31000640SS are three notable models that cater to the demands of data centers and enterprises. Each model is designed with specific features that enhance reliability and efficiency, making them suitable for various applications.

The Seagate ST3750630SS is a 750GB 15K RPM Serial Attached SCSI (SAS) drive. It boasts a high-performance architecture that allows for fast data transfer rates, making it ideal for high-load environments such as transaction processing and video streaming. This drive features an MTBF of 1.6 million hours, ensuring minimal downtime due to failures. It also employs advanced error recovery and data protection mechanisms, including error correction codes (ECC), to maintain data integrity.

Meanwhile, the ST3500620SS offers a capacity of 500GB with a spinning speed of 15K RPM as well. This drive utilizes the SAS interface, providing users with improved bandwidth and connectivity compared to traditional SATA drives. The ST3500620SS is designed with a focus on high availability, featuring a robust design that supports multiple workloads simultaneously. Its quick access times enhance overall system performance, making it a preferred choice for high-performance computing applications.

The ST31000640SS is another enterprise-class offering, delivering 1TB of storage capacity. Like its counterparts, this drive operates at 15K RPM and utilizes the SAS interface, facilitating fast data processing and retrieval. It also incorporates a dual-port design which allows for redundancy and failover capabilities. This feature is critical in enterprise environments where data access and uptime are paramount. The drive's design is optimized for durability and longevity, best suited for environments that require 24/7 operation.

All three Seagate drives feature advanced technologies such as dual-stage actuators and thermal write technology, ensuring improved read and write performance, along with reduced power consumption. Additionally, they are built to endure the rigors of enterprise workloads, including heavy I/O operations and high access demands.

In summary, the Seagate ST3750630SS, ST3500620SS, and ST31000640SS are exemplary models that reflect the company’s commitment to quality and performance in enterprise storage solutions. With their high speeds, reliability, and extensive features, these drives are well-equipped to meet the challenges of modern data-driven environments.
Top Page Image Contents