Seagate ST3750630SS, ST31000640SS, ST3500620SS manual Installation, Drive orientation

Page 43

8.0Installation

Barracuda ES.2 disk drive installation is a plug-and-play process. There are no jumpers, switches, or termina- tors on the drive.

SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays designed to accommodate the drive. In such systems, the host system typically provides a carrier or tray into which you need to mount the drive. Mount the drive to the carrier or tray provided by the host system using four 6-32 UNC screws. Do not over-tighten or force the screws. You can mount the drive in any orientation.

Note. SAS drives are designed to be attached to the host system without I/O or power cables. If you intend the use the drive in a non-backplane host system, connecting the drive using high-quality cables is acceptable as long as the I/O cable length does not exceed 4 meters (13.1 feet).

Slide the carrier or tray into the appropriate bay in your host system using the instructions provided by the host system. This connects the drive directly to your system’s SAS connector. The SAS connector is normally located on a SAS backpanel. See Section 9.4.1 for additional information about these connectors.

Power is supplied through the SAS connector.

The drive is shipped from the factory low-level formatted in 512-byte logical blocks. You need to reformat the drive only if you want to select a different logical block size.

Figure 10. Physical interface

8.1Drive orientation

The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two pre- ferred mounting orientations.

Barracuda ES.2 SAS Product Manual, Rev. E

39

Page 42 Page 44
Image 43
Page 42 Page 44
Contents ST31000640SS ST3750630SS ST3500620SS Barracuda ES.2 SASPage Contents Interface requirements Defect and error managementInstallation Seagate Technology support servicesScope Barracuda ES.2 SAS Product Manual, Rev. E Electromagnetic susceptibility Standards, compliance and reference documentsStandards Electromagnetic compatibilityCompliance Reference documents Barracuda ES.2 SAS Product Manual, Rev. E Barracuda ES.2 drive illustration General descriptionReliability Standard featuresMedia description PerformanceFormatted capacities Factory-installed optionsProgrammable drive capacity Barracuda ES.2 SAS Product Manual, Rev. E Seek performance Performance characteristicsInternal drive characteristics Access timeGeneral performance characteristics Format command execution time minutesStart/stop time Cache operation Prefetch/multi-segmented cache controlCaching write data Prefetch operation Unrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactPredictive failures Temperature Log Page 0DhThermal monitor Invoking DST State of the drive prior to testingDST failure definition ImplementationLog page entries Product warrantyShort test Function Code 001b Extended test Function Code 010bProduct repair and return information ShippingBarracuda ES.2 SAS Product Manual, Rev. E ST31000640SS DC power requirements Physical/electrical specificationsAC power requirements DC power requirementsST3500620SS DC power requirements ST3750630SS DC power requirementsCurrent profiles General DC power requirement notesPower sequencing Conducted noise immunityTypical ST31000640SS drive +5V and +12V current profiles Typical ST3500620SS drive +5V and +12V current profiles Power dissipationBarracuda ES.2 SAS Product Manual, Rev. E Environmental limits Temperature a. OperatingShock Relative humidityEffective altitude sea level a. Operating Shock and vibrationPackage size Packaged/product weight Drop height Corrosive environment Air cleanlinessVibration a. Operating-normal AcousticsX表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。 Physical dimensions Mechanical specificationsDrive internal defects/errors Defect and error managementDrive error recovery procedures 108.29 Background Media Scan SAS system errorsMedia Pre-Scan Idle Read After Write Deferred Auto-ReallocationDrive orientation InstallationAir flow CoolingGrounding Drive mountingBarracuda ES.2 SAS Product Manual, Rev. E Interface requirements SAS featuresDual port support Commands supported by Barracuda ES.2 SAS family drives Scsi commands supportedCommands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Inquiry data Mode Sense dataPage Mode Pages 2.1 ST31000640SS Mode Sense data2.2 ST3750630SS Mode Sense data 2.3 ST3500620SS Mode Sense data Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Connector requirements Physical characteristicsPin descriptions Electrical descriptionSAS pin descriptions Ready LED Out Signal characteristicsPower SAS transmitters and receiversEye masks Eye masks overview LED drive signalDifferential signals General interface characteristicsJitter tolerance masks Receive eye maskFrequency in kHz Peak-toSinusoidal JitterTransmitter signal characteristics Maximum allowable jitter Receiver signal characteristicsImpedance requirements Sheet 1 Impedance specificationsReceiver jitter tolerance Compliant jitter test pattern CjtpatImpedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5, 437dB Shows the zero-length test load Receiver characteristics Barracuda ES.2 SAS Product Manual, Rev. E Technical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index Page SAS See also cooling Page Seagate Technology LLC

ST31000640SS, ST3500620SS, ST3750630SS specifications

Seagate has been a leading name in the storage industry for decades, and its range of enterprise-class hard drives showcases advanced technologies and robust performance. The Seagate ST3750630SS, ST3500620SS, and ST31000640SS are three notable models that cater to the demands of data centers and enterprises. Each model is designed with specific features that enhance reliability and efficiency, making them suitable for various applications.

The Seagate ST3750630SS is a 750GB 15K RPM Serial Attached SCSI (SAS) drive. It boasts a high-performance architecture that allows for fast data transfer rates, making it ideal for high-load environments such as transaction processing and video streaming. This drive features an MTBF of 1.6 million hours, ensuring minimal downtime due to failures. It also employs advanced error recovery and data protection mechanisms, including error correction codes (ECC), to maintain data integrity.

Meanwhile, the ST3500620SS offers a capacity of 500GB with a spinning speed of 15K RPM as well. This drive utilizes the SAS interface, providing users with improved bandwidth and connectivity compared to traditional SATA drives. The ST3500620SS is designed with a focus on high availability, featuring a robust design that supports multiple workloads simultaneously. Its quick access times enhance overall system performance, making it a preferred choice for high-performance computing applications.

The ST31000640SS is another enterprise-class offering, delivering 1TB of storage capacity. Like its counterparts, this drive operates at 15K RPM and utilizes the SAS interface, facilitating fast data processing and retrieval. It also incorporates a dual-port design which allows for redundancy and failover capabilities. This feature is critical in enterprise environments where data access and uptime are paramount. The drive's design is optimized for durability and longevity, best suited for environments that require 24/7 operation.

All three Seagate drives feature advanced technologies such as dual-stage actuators and thermal write technology, ensuring improved read and write performance, along with reduced power consumption. Additionally, they are built to endure the rigors of enterprise workloads, including heavy I/O operations and high access demands.

In summary, the Seagate ST3750630SS, ST3500620SS, and ST31000640SS are exemplary models that reflect the company’s commitment to quality and performance in enterprise storage solutions. With their high speeds, reliability, and extensive features, these drives are well-equipped to meet the challenges of modern data-driven environments.
Top Page Image Contents