Seagate ST3300056FC (FDE) manual Reliability and service, Seek errors, Interface errors

Page 22

5.1.3Seek errors

A seek error is defined as a failure of the drive to position the heads to the addressed track. After detecting an initial seek error, the drive automatically performs an error recovery process. If the error recovery process fails, a seek positioning error (Error code = 15h or 02h) will be reported with a Hardware error (04h) in the Sense Key. Recoverable seek errors are specified at Less than 10 errors in 108 seeks. Unrecoverable seek errors (Sense Key = 04h) are classified as drive failures.

5.1.4Interface errors

An interface error is defined as a failure of the receiver on a port to recover the data as transmitted by the device port connected to the receiver. The error may be detected as a running disparity error, illegal code, loss of word sync, or CRC error. The total error rate for a loop of devices is the sum of the individual device error rates.

5.2Reliability and service

You can enhance the reliability of Cheetah 15K.6 disc drives by ensuring that the drive receives adequate cool- ing. Section 6.0 provides temperature measurements and other information that may be used to enhance the service life of the drive. Section 8.2 provides recommended air-flow information.

5.2.1Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)

These drives shall achieve an AFR of 0.55% (MTBF of 1,600,000 hours) when operated in an environment that ensures the HDA case temperatures do not exceed the values specified in Section 6.4.1.

Operation at case temperatures outside the specifications in Section 6.4.1 may increase the AFR (decrease the MTBF). AFR and MTBF statistics are poplulation statistics that are not relevant to individual units.

AFR and MTBF specifications are based on the following assumptions for Enterprise Storage System environ- ments:

•8,760 power-on hours per year

•250 average on/off cycles per year

•Operating at nominal voltages

•System provides adequate cooling to ensure the case temperatures specified in Section 6.4.1 are not exceeded.

5.2.2Preventive maintenance

No routine scheduled preventive maintenance is required.

5.2.3Hot plugging the drive

Inserting and removing the drive on the FC-AL will interrupt loop operation. The interruption occurs when the receiver of the next device in the loop must synchronize to a different input signal. FC error detection mecha- nisms, character sync, running disparity, word sync, and CRC are able to detect any error. Recovery is initiated based on the type of error.

The disc drive defaults to the FC-AL Monitoring state, Pass-through state, when it is powered-on by switching the power or hot plugged. The control line to an optional port bypass circuit (external to the drive), defaults to the Enable Bypass state. If the bypass circuit is present, the next device in the loop will continue to receive the output of the previous device to the newly inserted device. If the bypass circuit is not present, loop operation is temporarily disrupted until the next device starts receiving the output from the newly inserted device and regains synchronization to the new input.

The Pass-through state is disabled while the drive performs self test of the FC interface. The control line for an external port bypass circuit remains in the Enable Bypass state while self test is running. If the bypass circuit is

16

Cheetah 15K.6 FC Product Manual, Rev. C

Page 21 Page 23
Image 22
Page 21 Page 23
Contents ST3300656FC ST3450856FCST3146356FC Page Contents Installation Physical/electrical specificationsDefect and error management Interface requirementsSeagate Technology support services Cheetah 15K.6 FC Product Manual, Rev. C Scope Model Number Full Disk Encryption FDECheetah 15K.6 FC Product Manual, Rev. C Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityEuropean Union Restriction of Hazardous Substances RoHS Reference documents Ncits TR-20Cheetah 15K.6 FC Product Manual, Rev. C General description Standard features Reliability Media descriptionPerformance Formatted capacitiesFactory-installed options User-installed accessoriesSeek performance characteristics Performance characteristicsInternal drive characteristics Access timeStart/stop time Format command execution time minutesGeneral performance characteristics 176 144 100Cache operation Prefetch/multi-segmented cache controlCaching write data Prefetch operation Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T MillisecondsPredictive failures Temperature Log Page 0DhDetermining rate Thermal monitorDST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesShipping Product warrantyProduct repair and return information Cheetah 15K.6 FC Product Manual, Rev. C AC power requirements Physical/electrical specificationsDC power requirements ST3450856FC DC power requirements Gbit Amps ST3450056FC DC power requirements Gbit AmpsST3300656FC DC power requirements Gbit Amps ST3300056FC DC power requirements Gbit AmpsST3146356FC DC power requirements Gbit Amps ST3146756FC DC power requirements Gbit AmpsConducted noise immunity General DC power requirement notesPower sequencing Current profilesTypical ST3450856FC current profiles Typical ST3450056FC current profiles Typical ST3300656FC current profiles Typical ST3300056FC current profiles Typical ST3146356FC current profiles Typical ST3146756FC current profiles Power dissipation 450GB models300GB models Environmental limits Temperature146GB models Relative humidity Effective altitude sea levelShock and vibration Package size Packaged/product weight Drop heightShock Recommended mounting Acoustics Air cleanlinessVibration Corrosive environmentRoHS compliance statement Mechanical specifications Mounting configuration dimensionsDrive internal defects/errors Defect and error managementDrive error recovery procedures Page FC-AL system errors Background Media ScanDeferred Auto-Reallocation Media Pre-ScanIdle Read After Write Drive orientation InstallationDrive ID/option selection CoolingDrive mounting GroundingPage Cheetah 15K.6 FC Product Manual, Rev. C Link services supported Type of frame FC-AL featuresFibre Channel link service frames Interface requirementsFibre Channel task management responses Fibre Channel task management functionsFC Scsi FCP response codes Function name Response code Fibre Channel port login NPort login Plogi payload BytesNPort Login Accept ACC payload Bytes Fibre Channel port login acceptFibre Channel Process Login Process Login Plri payloadProcess Login Accept ACC payload Bytes Fibre Channel Process Login AcceptFibre Channel fabric login Fabric Login Flogi payload BytesFibre Channel fabric accept login Fabric Login Accept ACC payload BytesFibre Channel Arbitrated Loop options Scsi commands supportedDual port support FC-AL options supportedSupported commands Cheetah 15K.6 FC Product Manual, Rev. C Cheetah 15K.6 FC Product Manual, Rev. C Supported commands Inquiry data Mode Sense dataCheetah 15K.6 FC inquiry data Bytes Data hex Page Mode Data Header 000000 Cheetah 15K.6 FC Product Manual, Rev. C Supported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusFC-AL physical interface Physical characteristicsPhysical description Electrical description Connector requirementsPin descriptions Pin Signal name Signal type FC-SCA pin descriptions Pin Signal name Signal typeFC-AL transmitters and receivers Power Fault LED OutActive LED Out Enable port bypass signalsMotor start controls Parallel Enclosure Services Interface ESI 11 SEL6 through SEL0 ID linesArbitrated loop physical address Alpa values SettingHex Dec TTL input characteristics Signal characteristicsDevice control codes FC Differential output LED driver signalsFC Differential input Receive eye diagram Eye diagram data values Link rate GHz Cheetah 15K.6 FC Product Manual, Rev. C Presales Support Seagate Technology support servicesInternet Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call CenterToll-freeDirect dialFAX Index NumericsFC-AL Flogi Plogi Page See also cooling

ST3450056FC (FDE), ST3146756FC (FDE), ST3300056FC (FDE) specifications

Seagate has established itself as a leader in data storage solutions, and among its high-performance offerings are the Seagate ST3300056FC (FDE), ST3146756FC (FDE), and ST3450056FC (FDE) drives. These drives are part of Seagate's enterprise-class, 3.5-inch form factor family, providing robust data security, reliability, and performance for demanding data center environments.

The ST3300056FC boasts a capacity of 3TB, making it ideal for applications that require substantial storage space. With a 7200 RPM spindle speed and a 6Gb/s Serial Attached SCSI (SAS) interface, this drive delivers rapid data access speeds and high throughput, catering to the needs of enterprise workflows and data-intensive applications. The FDE (Full Disk Encryption) feature ensures that all stored data is encrypted, providing an added layer of protection against unauthorized access, which is critical for businesses handling sensitive information.

Similarly, the ST3146756FC offers a 1.4TB capacity, also spinning at 7200 RPM and utilizing a 6Gb/s SAS interface. As with its counterpart, this drive incorporates FDE technology, making it an excellent choice for environments that prioritize data security while maintaining performance. The SAS interface enhances connectivity options and further improves reliability and data integrity, essential for mission-critical applications.

The ST3450056FC, with a capacity of 4.5TB, stands out as a powerful option for storage needs that exceed traditional offerings. With the same 7200 RPM spindle speed and 6Gb/s SAS interface, it ensures optimal performance across various workloads. The FDE functionality further enhances its appeal, making it suitable for organizations that must comply with stringent data protection regulations.

All three drives are built with Seagate's advanced technologies, including PowerBalance, which maximizes the spindle performance while optimizing power consumption and thermal management. They are also designed with vibration tolerance, enhancing their reliability in multi-drive systems and environments where space and airflow may be limited.

In summary, the Seagate ST3300056FC, ST3146756FC, and ST3450056FC drives exemplify cutting-edge engineering, catering to enterprise needs with their impressive capacities, robust performance, and built-in security. They are well-suited for organizations that prioritize reliability and data integrity, making them a vital component of modern storage infrastructures.
Top Page Image Contents