Seagate ST3146756FC (FDE) manual Active LED Out, Enable port bypass signals, Motor start controls

Page 78

9.5.8Active LED Out

The Active LED Out signal is driven by the drive as indicated in Table 28.

Table 28: Active LED Out conditions

Normal command activity

LED status

 

 

Spun down and no activity

Slow blink (20% on and 80% off a 2 sec cycle)

 

 

Spun down and activity (command executing)

On

 

 

Spun up and no activity

On

 

 

Spun up and activity (command executing)

Off

 

 

Spinning up or down

Blinks steadily (50% on and 50% off)

 

 

Format in progress, each cylinder change

Toggles on/off

 

 

The Active LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +5 volt supply through an appropriate current limiting resistor. The LED and the current limiting resistor are external to the drive.

9.5.9Enable port bypass signals

The – Enable Bypass Port A (– EN BYP Port A) and – Enable Bypass Port B (– EN BYP Port B) signals control the port bypass circuits (PBC) located external to the disc drive. The PBC allows a loop to remain functional in the event of a drive failure or removal. When these signals are active, low, the PBC bypasses the drive on the associated port. When an Enable Bypass signal is active, the corresponding Port Bypass LED signal in con- nector J1 is driven low by the disc drive. A pull down resistor, 1K, located with the PBC should be used to insure the bypass is enabled if the disc drive is not installed.

The Enable Bypass signal is active under failing conditions within the drive, on detection of the Loop Port Bypass primitive sequence, or on removal of the drive. In the bypass state the drive continues to receive on the inbound fibre. Enable Bypass may be deactivated by detection of a Loop Port Enable primitive sequence if the drive has completed self-test and a hardware failure is not present.

Failure modes detected by the disc drive that will enable bypass include:

•Transmitter/receiver wrap test failure

•Loss of receive clock

•Loss of transmission clock

•Drive interface hardware error

9.5.10Motor start controls

The drive’s motor is started according to the Start_1 and Start_2 signals described in Table 29. The state of these signals can be wired into the backplane socket or driven by logic on the backplane.

Table 29:

Motor start control signals

 

 

 

 

 

Case

Start_2

Start_1

Motor spin function

 

 

 

 

1

Low

Low

Motor spins up at DC power on.

 

 

 

 

2

High

Low

Motor spins up only when SCSI Start command is received.

 

 

 

 

3

Low

High

Motor spins up after a delay of 12 seconds times the modulo 8 value

 

 

 

of the numeric SEL ID of the drive from DC power on.

 

 

 

 

4

High

High

The drive will not spin up.

 

 

 

 

72

Cheetah 15K.6 FC Product Manual, Rev. C

Page 77 Page 79
Image 78
Page 77 Page 79
Contents ST3450856FC ST3300656FCST3146356FC Page Contents Installation Physical/electrical specificationsDefect and error management Interface requirementsSeagate Technology support services Cheetah 15K.6 FC Product Manual, Rev. C Scope Model Number Full Disk Encryption FDECheetah 15K.6 FC Product Manual, Rev. C Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityEuropean Union Restriction of Hazardous Substances RoHS Reference documents Ncits TR-20Cheetah 15K.6 FC Product Manual, Rev. C General description Standard features Reliability Media descriptionPerformance Formatted capacitiesFactory-installed options User-installed accessoriesSeek performance characteristics Performance characteristicsInternal drive characteristics Access timeStart/stop time Format command execution time minutesGeneral performance characteristics 176 144 100Prefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T MillisecondsPredictive failures Temperature Log Page 0DhDetermining rate Thermal monitorDST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesProduct warranty ShippingProduct repair and return information Cheetah 15K.6 FC Product Manual, Rev. C Physical/electrical specifications AC power requirementsDC power requirements ST3450856FC DC power requirements Gbit Amps ST3450056FC DC power requirements Gbit AmpsST3300656FC DC power requirements Gbit Amps ST3300056FC DC power requirements Gbit AmpsST3146356FC DC power requirements Gbit Amps ST3146756FC DC power requirements Gbit AmpsConducted noise immunity General DC power requirement notesPower sequencing Current profilesTypical ST3450856FC current profiles Typical ST3450056FC current profiles Typical ST3300656FC current profiles Typical ST3300056FC current profiles Typical ST3146356FC current profiles Typical ST3146756FC current profiles Power dissipation 450GB models300GB models Temperature Environmental limits146GB models Relative humidity Effective altitude sea levelPackage size Packaged/product weight Drop height Shock and vibrationShock Recommended mounting Acoustics Air cleanlinessVibration Corrosive environmentRoHS compliance statement Mechanical specifications Mounting configuration dimensionsDefect and error management Drive internal defects/errorsDrive error recovery procedures Page FC-AL system errors Background Media ScanMedia Pre-Scan Deferred Auto-ReallocationIdle Read After Write Drive orientation InstallationDrive ID/option selection CoolingDrive mounting GroundingPage Cheetah 15K.6 FC Product Manual, Rev. C Link services supported Type of frame FC-AL featuresFibre Channel link service frames Interface requirementsFibre Channel task management functions Fibre Channel task management responsesFC Scsi FCP response codes Function name Response code Fibre Channel port login NPort login Plogi payload BytesNPort Login Accept ACC payload Bytes Fibre Channel port login acceptFibre Channel Process Login Process Login Plri payloadProcess Login Accept ACC payload Bytes Fibre Channel Process Login AcceptFibre Channel fabric login Fabric Login Flogi payload BytesFibre Channel fabric accept login Fabric Login Accept ACC payload BytesFibre Channel Arbitrated Loop options Scsi commands supportedDual port support FC-AL options supportedSupported commands Cheetah 15K.6 FC Product Manual, Rev. C Cheetah 15K.6 FC Product Manual, Rev. C Supported commands Mode Sense data Inquiry dataCheetah 15K.6 FC inquiry data Bytes Data hex Page Mode Data Header 000000 Cheetah 15K.6 FC Product Manual, Rev. C Supported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusPhysical characteristics FC-AL physical interfacePhysical description Connector requirements Electrical descriptionPin descriptions FC-SCA pin descriptions Pin Signal name Signal type Pin Signal name Signal typeFC-AL transmitters and receivers Power Fault LED OutEnable port bypass signals Active LED OutMotor start controls Parallel Enclosure Services Interface ESI 11 SEL6 through SEL0 ID linesSetting Arbitrated loop physical address Alpa valuesHex Dec Signal characteristics TTL input characteristicsDevice control codes LED driver signals FC Differential outputFC Differential input Receive eye diagram Eye diagram data values Link rate GHz Cheetah 15K.6 FC Product Manual, Rev. C Presales Support Seagate Technology support servicesInternet Technical SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call CenterToll-freeDirect dialFAX Index NumericsFC-AL Flogi Plogi Page See also cooling

ST3450056FC (FDE), ST3146756FC (FDE), ST3300056FC (FDE) specifications

Seagate has established itself as a leader in data storage solutions, and among its high-performance offerings are the Seagate ST3300056FC (FDE), ST3146756FC (FDE), and ST3450056FC (FDE) drives. These drives are part of Seagate's enterprise-class, 3.5-inch form factor family, providing robust data security, reliability, and performance for demanding data center environments.

The ST3300056FC boasts a capacity of 3TB, making it ideal for applications that require substantial storage space. With a 7200 RPM spindle speed and a 6Gb/s Serial Attached SCSI (SAS) interface, this drive delivers rapid data access speeds and high throughput, catering to the needs of enterprise workflows and data-intensive applications. The FDE (Full Disk Encryption) feature ensures that all stored data is encrypted, providing an added layer of protection against unauthorized access, which is critical for businesses handling sensitive information.

Similarly, the ST3146756FC offers a 1.4TB capacity, also spinning at 7200 RPM and utilizing a 6Gb/s SAS interface. As with its counterpart, this drive incorporates FDE technology, making it an excellent choice for environments that prioritize data security while maintaining performance. The SAS interface enhances connectivity options and further improves reliability and data integrity, essential for mission-critical applications.

The ST3450056FC, with a capacity of 4.5TB, stands out as a powerful option for storage needs that exceed traditional offerings. With the same 7200 RPM spindle speed and 6Gb/s SAS interface, it ensures optimal performance across various workloads. The FDE functionality further enhances its appeal, making it suitable for organizations that must comply with stringent data protection regulations.

All three drives are built with Seagate's advanced technologies, including PowerBalance, which maximizes the spindle performance while optimizing power consumption and thermal management. They are also designed with vibration tolerance, enhancing their reliability in multi-drive systems and environments where space and airflow may be limited.

In summary, the Seagate ST3300056FC, ST3146756FC, and ST3450056FC drives exemplify cutting-edge engineering, catering to enterprise needs with their impressive capacities, robust performance, and built-in security. They are well-suited for organizations that prioritize reliability and data integrity, making them a vital component of modern storage infrastructures.
Top Page Image Contents