JVC DT-V20L1 Available signals, Video signals, Computer signals preset DVI-D HDCP terminals

7Available signals

The following signals are available for this monitor.

Video signals

			Input terminal
No.	Signal name	VIDEO	COMPO./RGB	HD/SD SDI (IN 1, IN 2)*1	DVI-D (HDCP)
			(Analog component/	(DT-V24L1D and	(Digital component/digital
		(INPUT1, INPUT2)
			analog RGB)	DT-V20L1D only)	RGB)
1	NTSC	√	—	—	—
2	PAL	√	—	—	—
3	SECAM	√	—	—	—
4	BW(50Hz/60Hz)	√	—	—	—
5	480/60i	—	√	√	—
6	576/50i	—	√	√	—
7	480/60p	—	√	—	√
8	576/50p	—	√	—	√
9	640∗480/60p	—	—	—	√
10	720/60p	—	√	√	√
11	720/50p	—	√	√	√
12	720/30p	—	√	√	—
13	720/25p	—	√	√	—
14	720/24p	—	√	√	—
15	1080/60i	—	√	√	√
16	1035/60i	—	√*2	√	—
17	1080/50i	—	√	√	√
18	1080/60p	—	—	—	√
19	1080/50p	—	—	—	√
20	1080/30p	—	√	√	√
21	1080/25p	—	√	√	√
22	1080/24p	—	√	√	√
23	1080/30psF	—	√*3	√*3	—
24	1080/24psF	—	√	√	—

√: Acceptable

—: Not acceptable

*1 Compatible with EMBEDDED AUDIO

*2 Displays the picture as 1080/60i, and “1080/60i” is displayed in the status display (☞ page 7). *3 “1080/60i” is displayed in the status display (☞ page 7).

Computer signals (preset)

DVI-D (HDCP) terminals

No.	Signal name	Screen resolution		Horizontal	Vertical	Scan system
		Horizontal	Vertical	frequency (kHz)	frequency (Hz)
1	VGA60	640	480	31.5	59.9	Non-interlace
2	WVGA60	852	480	31.5	59.9	Non-interlace
3	SVGA60	800	600	37.9	60.3	Non-interlace
4	XGA60	1024	768	48.4	60.0	Non-interlace
5	WXGA (1280)	1280	768	47.8	60.0	Non-interlace
6	SXGA60	1280	1024	64.0	60.0	Non-interlace
7	WSXGA+60	1680	1050	65.2	60.0	Non-interlace
8	UXGA60*4	1600	1200	75.0	60.0	Non-interlace
9	WUXGA60*4	1920	1200	74.0	59.9	Non-interlace
10	720/60p	1280	720	45.0	59.9/60.0	Non-interlace
11	1080/60p*4	1920	1080	67.5	59.9/60.0	Non-interlace

*4 For DT-V20L1D and DT-V20L1: When No. 8, 9 or 11 signal is input, thin lines will become obscured because their signal resolution is higher than the screen resolution.

Specification of DVI-D (HDCP) terminal

Connect it to DVI-D output terminal on a personal computer.

Pin	Input signal		Pin	Input signal		Pin	Input signal
No.			No.			No.
1	T.M.D.S Data 2–		9	T.M.D.S Data 1–		17	T.M.D.S Data 0–
2	T.M.D.S Data 2+		10	T.M.D.S Data 1+		18	T.M.D.S Data 0+
3	T.M.D.S Data 2 shield	11		T.M.D.S Data 1 shield	19		T.M.D.S Data 0 shield
4	NC	12		NC	20		NC
5	NC	13		NC	21		NC
6	DDC Clock	14		+5 V Power	22		T.M.D.S Clock shield
7	DDC Data	15		GND	23		T.M.D.S Clock+
8	NC		16	Hot Plug Detect		24	T.M.D.S Clock–

Note for analog component/analog RGB signals

The monitor is compatible with G on sync, Y on sync and composite sync (Cs) signals. The monitor is not compatible with separate sync (HS/VS) signals.

Note for computer signals

•Non-preset signals may not be displayed normally even if its frequency is within the acceptable range.

•When a preset signal is input, the signal format is displayed on the screen. For other signals, the resolution is displayed.

Note for connections

•Before making any connections, turn off all the equipment.

•Use a cord whose plugs correctly match the terminals on this monitor and the equipment.

•Plugs should be firmly inserted; poor connections could cause noise.

•When unplugging a cord, be sure to grasp its plug and pull it out.

•DO NOT connect the power cord until all connections are completed.

•Refer also to the user manual of each piece of equipment.

9