JVC DT-V20L1D Specifications, General, Input/output terminals, DT-V24L1D/DT-V24L1

Specifications

7 General

Model name		DT-V24L1D/DT-V24L1				DT-V20L1D/DT-V20L1
Type	Multi format LCD monitor
Screen size	Type 24 wide format				Type 20 wide format
Aspect ratio	16:10
LCD panel	24˝ wide, active matrix TFT				20˝ wide, active matrix TFT
Effective screen size	Width	: 518.4 mm (20 3/8˝)			Width	: 433.4 mm (17 1/16˝)
	Height	: 324 mm (12 3/4˝)			Height	: 270.9 mm (10 5/8˝)
Number of pixels displayed	1 920 x 1 200				1 680 x 1 050
Number of colors displayed	16.77 million (256 colors for each RGB)
Viewing angle (TYP.)	176° (Horizontally), 176° (Vertically)				170° (Horizontally), 170° (Vertically)
Brightness (at least) (TYP.)	400 cd/m2
Contrast ratio (TYP.)	1 000:1				800:1
Horizontal/vertical frequency	H	: 31.469 kHz – 75.000 kHz			H	: 31.469 kHz – 75.000 kHz
(computer signal)	V	: 60 Hz ± 5 Hz			V	: 60 Hz ± 5 Hz
	* Some signals within this frequency range may not be displayed (“Out of range” is
	displayed).
Compliant video signal format	☞ “Available signals” on page 9
Format	HD SDI	: BTA S-004B, SMPTE292M
(DT-V24L1D and DT-V20L1D only)	SD SDI	: ITU-R BT.656		: 525/625
		SMPTE259M		: 525
	EMBEDDED AUDIO		: SMPTE299M, SMPTE272M
Audio output	Internal speaker		: 1 W + 1 W
Operating conditions	Operating temperature			: 5° C – 35 °C (41 °F – 95 °F)
	Operating humidity			: 20 % – 80 % (non-condensing)
	* Slightly variable depending on ambient conditions for installation.
Power requirements	AC 120 V/AC 220 – 240 V, 50 Hz/60 Hz
Rated current	1.15 A (AC 120 V)/0.67 A (AC 220 – 240 V)				1.00 A (AC 120 V)/0.60 A (AC 220 – 240 V)
External dimensions	Width	: 564 mm (22 1/4˝)		564 mm (22 1/4˝)	Width	: 477 mm (18 7/8˝)	477 mm (18 7/8˝)
(excluding protruding parts)	Height : 448.6 mm (17 3/4˝) 408 mm (16 1/8˝)				Height : 394.6 mm (15 5/8˝) 354 mm (14˝)
	Depth	: 243 mm (9 5/8˝)		99 mm (4˝)	Depth	: 243 mm (9 5/8˝)	99 mm (4˝)
		(with the stand)		(without the		(with the stand)	(without the
				stand)			stand)
Weight	11.6 kg (25.5 lbs) (with the stand)				10.3 kg (22.7 lbs) (with the stand)
	8.7 kg (19.1 lbs) (without the stand)				7.4 kg (16.3 lbs) (without the stand)
Accessories	AC power cord x 1, Power cord holder x 1, Screw x 2 (for power cord holder)

7Input/output terminals

Model name			DT-V24L1D/DT-V20L1D		DT-V24L1/DT-V20L1
	VIDEO	Input/output of composite signal
	(INPUT 1)
			: 1 line, BNC connector x 2, 1 V(p-p), 75 Ω
	VIDEO
		*	The input (IN) and output (OUT) terminals are bridge-connected (auto termination).
	(INPUT 2)
	DVI-D (HDCP)	DVI-D signal input (compatible with HDCP)
			: DVI-D connector x 1 (compatible with DDC2B)
	COMPO./RGB	Input/output of analog component signal/analog RGB signal
	(G/Y, B/PB/B-Y,		: 1 line, BNC connector x 6		: 1 V(p-p), 75 Ω (including sync signal)
	R/PR/R-Y)		Video signal	: G/Y
				B/PB/B-Y, R/PR/R-Y	: 0.7 V(p-p), 75 Ω
		*	The input (IN) and output (OUT) terminals are bridge-connected (auto termination).
Video	EXT.SYNC (CS)	Input/output of composite sync signal
			: 1 line, BNC connector x 2,
			0.3 V(p-p) – 4 V(p-p),
			75 Ω (tri-level sync, negative polarity sync (bi-level), and BB)
			(including no video signal)
		*	The input (IN) and output (OUT) terminals are bridge-connected (auto termination).
	HD/SD SDI (IN 1)	Digital signal input
	HD/SD SDI (IN 2)	(compatible with EMBEDDED AUDIO)
			: auto detection, 1 line,
			BNC connector x 1
	HD/SD SDI	Digital signal output
	(SWITCHED OUT) (compatible with EMBEDDED AUDIO)

:1 line switched out, BNC connector x 1

	AUDIO ASSIGN
Audio	(IN 1)	Analog audio signal input	: 1 line, RCA connector x 2,
	(IN 2)		500 mV (rms), high impedance
	AUDIO ASSIGN
	AUDIO ASSIGN	Analog audio signal output	: 1 line, RCA connector x 2,
	(MONITOR OUT)		500 mV (rms)
control	REMOTE (MAKE/	☞ “Using the MAKE/TRIGGER system” on page 14
	TRIG.)
External	REMOTE
	(RS-485)	☞ “Using the serial communication” on page 15
	REMOTE
	(RS-232C)

Notice on transportation

This monitor is precision equipment and needs dedicated packing material for transportation. Never use any packing material supplied from sources other than JVC or JVC-authorized dealers.

Options (not supplied)

RACK MOUNT ADAPTER (DT-V20L1D and DT-V20L1 only): RK-C20L1

•For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed, and may be slightly different from actual products.

•Design and specifications are subject to change without notice.

•All company names and product names mentioned herein are used for identification purposes only, and may be the trademarks or registered trademarks of their respective companies.

17