JVC DT-V24L1D, DT-V20L1 Setting of “sub menu POSI.”, Setting of “E.AUDIO GROUP”, Other Setting

Operation guide Shows the buttons for each operation.

NOTE

•The menu automatically disappears in about 30 seconds after the last menu operation.

•Some items may not appear on the menu depending on the input or the input signal. These items are not available.

Technical information

Setting of “sub menu POSI.”

The setting values and features are as follows.

LOWER1 : Displays the current setting and adjustment bar at the lower part of the screen.

UPPER1 : Displays the current setting and adjustment bar at the upper part of the screen.

LOWER2 : Displays the current setting at the lower part of the screen.

UPPER2 : Displays the current setting at the upper part of the screen.

NOTE

The adjustment bar is not displayed for some items.

Setting of “E.AUDIO GROUP”

The setting values and selectable audio channels of EMBEDDED AUDIO are as follows.

1G : channel(s) 1/2/3/4/1+2/3+4/1 – 4 (1G)

2G : channel(s) 5/6/7/8/5+6/7+8/5 – 8 (2G)

1-2G : channel(s) 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/1 – 8 (1G+2G)

3G : channel(s) 9/10/11/12/9+10/11+12/9 – 12 (3G)

1-3G : channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/1+2/3+4/5+6/7+8/9+10/11+12/1 – 4 (1G)/5 – 8 (2G)/9 – 12 (3G)/1

– 8 (1G+2G)/1 – 12 (1-3G)

Example of the level meter display—Level indication and audio channels

Ex.: When “LEVEL METER ch” is set to “12:78” and ”BAR TYPE” is set to “3COLORS.”

OTHER SETTING

Setting for the “sub menu” and color system

Item	To do	Setting value
sub menu POSI.	Select the contents and displaying position of “sub menu.”	☞ “Technical information”
COLOR SYSTEM	Select the color system.	AUTO, NTSC, PAL, SECAM
	• If the picture is unstable with “AUTO,” select the appropriate
	color system other than “AUTO.”

AUDIO SETTING

Setting for the audio input/output

Item		To do	Setting value
BALANCE		Adjust the balance between the right and left	L5 – L1, 0, R1 – R5
		speakers.
AUDIO1 ASSIGN.		Select the video input which the audio signal	SDI-1*1, SDI-2*1, DVI, COMP/RGB, VIDEO-1,
		through AUDIO ASSIGN (IN 1) terminal is	VIDEO-2
		assigned to.
AUDIO2 ASSIGN.		Select the video input which the audio signal
		through AUDIO ASSIGN (IN 2) terminal is
		assigned to.
E.AUDIO		Select the audio channel group of the	☞ “Technical information”
GROUP*1, 2		EMBEDDED AUDIO signals.
LEVEL METER		Adjust the audio level meter display for the EMBEDDED AUDIO signals (☞ “Technical
SETTING*1, 2		information”).
	LEVEL	Select the audio channels used in the audio	OFF, 12:78 (Displays the channels 1 – 6 at the
	METER ch	level meter display.	top left of the screen and 7 – 12 at the top right.),
			13:24 (Displays the odd channels at the top left
			of the screen and the even channels at the top
			right.)
	BAR TYPE	Select the color of the audio level meter display.	3COLORS (3 colors to indicate variations in
			input levels), W.100 (white)
	REFERENCE	Select the standard input level.	–20dB, –18dB
	LEVEL
	OVER LEVEL	Select the input level’s lower limit indicated in	–10dB, –8dB, –6dB, –4dB, –2dB
		red for the “3COLORS” display.
	BAR	Select the brightness of the audio level meter	HIGH, LOW
	BRIGHTNESS	display.

NOTE

•When selecting “BALANCE,” the adjustment bar is displayed at the lower part of the screen.

•You cannot select the same input for both “AUDIO1 ASSIGN.” and “AUDIO2 ASSIGN.”

SYNC FUNCTION

Setting for the synchronization with signals

Item	To do	Setting value
NO SYNC ACTION	Select the screen status when no signal is being	OFF, SUSPEND (suspend mode),
	input.	GRAY B.(gray screen)
DELAY TIME	Select the period until the screen status	5sec., 20sec., 1min., 15min., 30min.
	changes after signals stop coming in.
SYNC INPUT SEL.*2	Select the sync signal for the VIDEO and	INT., EXT.
	COMPO./RGB input.

NOTE

•When “BAR TYPE” is set to “W.100,” the standard input level set in the “REFERENCE LEVEL” is displayed with the line indication. The input level set in “OVER LEVEL” is not displayed.

•The audio channel bar with no signal input is displayed in white for “3COLORS,” and in gray for “W.100.”

OVER LEVEL REFERENCE LEVEL

Red

Yellow

Green

QUICK SWITCHING Select the quickness for switching the input. STD., QUICK

*1 DT-V24L1D and DT-V20L1D only *2 Memorized for each input.

11