Seagate ST3146756FC (FDE), ST3300056FC (FDE) manual FC-AL system errors, Background Media Scan

Page 51

Table 8: Read and write retry count maximum recovery times [1]

Read retry

Maximum recovery time per LBA

count

(cumulative, msec)

 

 

0

51.87

 

 

1

59.85

 

 

2

203.49

 

 

3

219.45

 

 

4

231.42

 

 

5

297.38

 

 

6

323.62

 

 

7

355.54

 

 

8

439.39

 

 

9

507.39

 

 

10

539.31

 

 

11

567.24

 

 

12

1,460.86

 

 

13 (default)

1,468.74

 

 

[1]These values are subject to change.

Write retry

Maximum recovery time per LBA

count

(cumulative, msec)

 

 

0

23.94

 

 

1

35.91

 

 

2

55.86

 

 

3

67.83

 

 

4

119.79

 

 

5 (default)

147.72

 

 

Setting these retry counts to a value below the default setting could result in an increased unrecovered error rate which may exceed the value given in this product manual. A setting of zero (0) will result in the drive not performing error recovery.

For example, suppose the Read/Write Recovery page has the RC bit set to 0, read retry count set to 4, and the recovery time limit field (Mode Sense page 01, bytes 10 and 11) set to FF FF hex (maximum). A four LBA Read command is allowed to take up to 253.11 msec recovery time for each of the four LBAs in the command. If the recovery time limit is set to 00 C8 hex (200 msec decimal) a four LBA read command is allowed to take up to 200 msec for all error recovery within that command. The use of the Recovery Time Limit field allows finer granularity on control of the time spent in error recovery. The recovery time limit only starts counting when the drive is executing error recovery and it restarts on each command. Therefore, each command’s total recovery time is subject to the recovery time limit. Note: A recovery time limit of 0 will use the drive’s default value of FF FF. Minimum recovery time limit is achieved by setting the Recovery Time Limit field to 00 01.

7.3FC-AL system errors

Information on the reporting of operational errors or faults across the interface is given in the Fibre Channel Interface Manual. The FCP Response returns information to the host about numerous kinds of errors or faults. The Receive Diagnostic Results reports the results of diagnostic operations performed by the drive.

Status returned by the drive to the initiator is described in the Fibre Channel Interface Manual. Status reporting plays a role in systems error management and its use in that respect is described in sections where the various commands are discussed.

7.4Background Media Scan

Background Media Scan (BMS) is a self-initiated media scan. BMS is defined in the T10 document SPC-4 available from the T10 committee. BMS performs sequential reads across the entire pack of the media while the drive is idle. In RAID arrays, BMS allows hot spare drives to be scanned for defects prior to being put into service by the host system. On regular duty drives, if the host system makes use of the BMS Log Page, it can

Cheetah 15K.6 FC Product Manual, Rev. C

45

Page 50 Page 52
Image 51
Page 50 Page 52
Contents ST3450856FC ST3300656FCST3146356FC Page Contents Interface requirements Physical/electrical specificationsDefect and error management InstallationSeagate Technology support services Cheetah 15K.6 FC Product Manual, Rev. C Model Number Full Disk Encryption FDE ScopeCheetah 15K.6 FC Product Manual, Rev. C Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityEuropean Union Restriction of Hazardous Substances RoHS Ncits TR-20 Reference documentsCheetah 15K.6 FC Product Manual, Rev. C General description Standard features Formatted capacities Media descriptionPerformance ReliabilityUser-installed accessories Factory-installed optionsAccess time Performance characteristicsInternal drive characteristics Seek performance characteristics176 144 100 Format command execution time minutesGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Unrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsMilliseconds 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Temperature Log Page 0DhDetermining rate Predictive failuresImplementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct warranty ShippingProduct repair and return information Cheetah 15K.6 FC Product Manual, Rev. C Physical/electrical specifications AC power requirementsDC power requirements ST3450056FC DC power requirements Gbit Amps ST3450856FC DC power requirements Gbit AmpsST3300056FC DC power requirements Gbit Amps ST3300656FC DC power requirements Gbit AmpsST3146756FC DC power requirements Gbit Amps ST3146356FC DC power requirements Gbit AmpsCurrent profiles General DC power requirement notesPower sequencing Conducted noise immunityTypical ST3450856FC current profiles Typical ST3450056FC current profiles Typical ST3300656FC current profiles Typical ST3300056FC current profiles Typical ST3146356FC current profiles Typical ST3146756FC current profiles 450GB models Power dissipation300GB models Temperature Environmental limits146GB models Effective altitude sea level Relative humidityPackage size Packaged/product weight Drop height Shock and vibrationShock Recommended mounting Corrosive environment Air cleanlinessVibration AcousticsRoHS compliance statement Mounting configuration dimensions Mechanical specificationsDefect and error management Drive internal defects/errorsDrive error recovery procedures Page Background Media Scan FC-AL system errorsMedia Pre-Scan Deferred Auto-ReallocationIdle Read After Write Cooling InstallationDrive ID/option selection Drive orientationGrounding Drive mountingPage Cheetah 15K.6 FC Product Manual, Rev. C Interface requirements FC-AL featuresFibre Channel link service frames Link services supported Type of frameFibre Channel task management functions Fibre Channel task management responsesFC Scsi FCP response codes Function name Response code NPort login Plogi payload Bytes Fibre Channel port loginProcess Login Plri payload Fibre Channel port login acceptFibre Channel Process Login NPort Login Accept ACC payload BytesFabric Login Flogi payload Bytes Fibre Channel Process Login AcceptFibre Channel fabric login Process Login Accept ACC payload BytesFabric Login Accept ACC payload Bytes Fibre Channel fabric accept loginFC-AL options supported Scsi commands supportedDual port support Fibre Channel Arbitrated Loop optionsSupported commands Cheetah 15K.6 FC Product Manual, Rev. C Cheetah 15K.6 FC Product Manual, Rev. C Supported commands Mode Sense data Inquiry dataCheetah 15K.6 FC inquiry data Bytes Data hex Page Mode Data Header 000000 Cheetah 15K.6 FC Product Manual, Rev. C Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features Supported Feature or conditionPhysical characteristics FC-AL physical interfacePhysical description Connector requirements Electrical descriptionPin descriptions FC-SCA pin descriptions Pin Signal name Signal type Pin Signal name Signal typeFC-AL transmitters and receivers Fault LED Out PowerEnable port bypass signals Active LED OutMotor start controls 11 SEL6 through SEL0 ID lines Parallel Enclosure Services Interface ESISetting Arbitrated loop physical address Alpa valuesHex Dec Signal characteristics TTL input characteristicsDevice control codes LED driver signals FC Differential outputFC Differential input Receive eye diagram Eye diagram data values Link rate GHz Cheetah 15K.6 FC Product Manual, Rev. C Technical Support Seagate Technology support servicesInternet Presales SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call CenterToll-freeDirect dialFAX Numerics IndexFC-AL Flogi Plogi Page See also cooling

ST3450056FC (FDE), ST3146756FC (FDE), ST3300056FC (FDE) specifications

Seagate has established itself as a leader in data storage solutions, and among its high-performance offerings are the Seagate ST3300056FC (FDE), ST3146756FC (FDE), and ST3450056FC (FDE) drives. These drives are part of Seagate's enterprise-class, 3.5-inch form factor family, providing robust data security, reliability, and performance for demanding data center environments.

The ST3300056FC boasts a capacity of 3TB, making it ideal for applications that require substantial storage space. With a 7200 RPM spindle speed and a 6Gb/s Serial Attached SCSI (SAS) interface, this drive delivers rapid data access speeds and high throughput, catering to the needs of enterprise workflows and data-intensive applications. The FDE (Full Disk Encryption) feature ensures that all stored data is encrypted, providing an added layer of protection against unauthorized access, which is critical for businesses handling sensitive information.

Similarly, the ST3146756FC offers a 1.4TB capacity, also spinning at 7200 RPM and utilizing a 6Gb/s SAS interface. As with its counterpart, this drive incorporates FDE technology, making it an excellent choice for environments that prioritize data security while maintaining performance. The SAS interface enhances connectivity options and further improves reliability and data integrity, essential for mission-critical applications.

The ST3450056FC, with a capacity of 4.5TB, stands out as a powerful option for storage needs that exceed traditional offerings. With the same 7200 RPM spindle speed and 6Gb/s SAS interface, it ensures optimal performance across various workloads. The FDE functionality further enhances its appeal, making it suitable for organizations that must comply with stringent data protection regulations.

All three drives are built with Seagate's advanced technologies, including PowerBalance, which maximizes the spindle performance while optimizing power consumption and thermal management. They are also designed with vibration tolerance, enhancing their reliability in multi-drive systems and environments where space and airflow may be limited.

In summary, the Seagate ST3300056FC, ST3146756FC, and ST3450056FC drives exemplify cutting-edge engineering, catering to enterprise needs with their impressive capacities, robust performance, and built-in security. They are well-suited for organizations that prioritize reliability and data integrity, making them a vital component of modern storage infrastructures.
Top Page Image Contents