Manuals / Clover Electronics / TV and Video / Flat Panel Television

Clover Electronics LCD2088, LCD2084 Sensor Connection and Relay in &OUT Sensor Connection Sensor

Models: LCD2084 LCD2088

1 176

Download 176 pages 21.01 Kb

Page 26

Stand-alone DVR Instruction Manual

Note:

-Pay attention to not make scratches or dents on the surface of panel (screen) during installation of the system.

-In case of this, the warranty will be voided.

5-4.2.1. Connection of Composite Monitor

If necessary, connect the composite Video Output (yellow RCA) and Audio Output (white RCA) to Video IN and Audio IN on a composite monitor or TV (RCA cable: not included).

5-4.3. Sensor Connection and RELAY IN &OUT

▫SENSOR Connection (SENSOR IN)

Connect up to 8 sensors to ALM (SENSOR) IN. The Sensors should be contactor type and support N.O. (Normal Open).

- + NO C NC G 8 7 6 5 4 3 2 1

RS485 ALARM

ALARM IN

[Fig. 5-6 SENSOR IN PIN]

▫ALARM OUT Connection

When necessary, use ALARM OUT. The ALARM OUTPUT is a relay contactor type and supports N.O. (Normal Open) and N.C. (Normal Close). The Output capacity is 220V 1A. A higher capacity can cause system failure.

- + NO C NC G 8 7 6 5 4 3 2 1

RS485 ALARM

ALARM IN

[Fig. 5-7 Alarm Output]

26

Image 26

Clover Electronics LCD2088, LCD2084 Sensor Connection and Relay in &OUT Sensor Connection Sensor, Alarm OUT Connection

Contents

Wide LCD Screen Ver , 061009Page Contents Video Enhance 100 133 159 Page About this manual Page Unpacking 1 Wide LCD Panel Built-in 8 Ch Digital Video Recorder Wide Screen Automatic System RecoveryHigh Resolution DVR 720 x Multi Functional RecordPage What to do at the time of Installation System should be installed in the following orderPage Specifications Specifications Installation Controls and ConnectorsControls and Connectors Front/Top ViewREC Key Stand-by Power Mode ButtonRemote Control Signal Receiver Enter KeyRear Installation System Connection System ConnectionInstallation of the system on the wall InstallationInstallation of the Monitor Camera Connection Connection of 6pin Mini DIN CamerasAlarm OUT Connection Sensor Connection and Relay in &OUT Sensor Connection Sensor4. RS485 Connection RS485 ConnectionPower Cable Connection 10 Power cable connectionHow to operate Playback Devices SET the Start Time General Information Operating Interface IR Remote Controller Power On/Off STAND-BY Power Mode ButtonPower button on Menu window By clicking the mouseMenu Window Menu WindowDisplay Screen Full ScreenSplit Screens Full Screen Sequencing Screen Quad Screen Live Split ScreenSequencing Screens Sequencing screenLive Audio Audio on , Audio OFFCommunication Between Monitor and Cameras Zoom 11 Zoomed screenOSD on /OFF is possible in the Live mode or Record mode OSD on / OFFPAN / Tilt 14 PAN/TILT buttonPAN / Tilt Channel Selection and Screen ConversionZoom / Focus IrisPreset Execution PresetPreset Setup System Status 18 System Status buttonPower Loss Lists Power Loss Lists21 Power Loss Lists Message Video Loss List 22 Video Loss Lists window24 Video Loss Lists Message window Video Enhance Camera Input Config Contrast / Brightness 27 Camera InputVGA Output Config Scale / Contrast / Brightness / Saturation Manual Event Recording RecordManual Continuous recording Timer Recording 30 should be turned onTimer Event Recording 32 Timer Event Recording setupAudio Recording Estimated Recording TimeRecording Icons 37 Recording IconsReplay ReplayQuick Replay Playback Devices Set the Start TimeBy using the Replay Time set-up buttons By using the Replay Time set-up barPage ④ Prev / Next ② Play / Pause③ REW/FF Disappearance of Replay control buttons 45 Split screen during replaying Copy Copying devicesRegards to blank Medias CD-R/W and DVD-R/W Set the Copy Start Time Copying extentBy using the Copy Start/End set-up buttons 49 Copy Start time and Channel Selection windowBy using the Start/End set-up bar Set the Copy End Time Copying extentCopying the recorded data during replaying Set the ending time and date to copy as described aboveCD-RW Copy Select Copy ModeUSB Copy DVD-RW CopyCopying the AVI File Format 54 Copying IconSetup Factory Default Load Config / Backup ConfigManual Recording Timer Recording Schedule RecordingTimer Event Recording Manual Event RecordingSetup Setup Setup Icon on Menu windowSystem System Name System name buttonTime Format LanguageTime / Date Date Format DisplaySystem Config Factory Default 14 Factory Default buttonLoad Config / Backup Config Load ConfigBackup Config 18 Backup Config buttonON/OFF PasswordPassword Change IR Remote ID 21 IR Remote ID buttonBy DvrMaster GUI Firmware UpdateBy USB memory System InfoDisk Manager Format HDD Write FailHDD Overwrite Camera Camera ON/OFF Camera Name Camera TitleBuzzer RelayPan/Tilt Settings 35 PAN/TILT button37 PAN/TILT 41 Baudrate button Parity Bit PTZ IDDisplay Sequencing dwell timeMicrophone Volume AudioRecord Record Icon DisplayAll Manual / Timer recording button 56 All Manual / Timer buttonAll Motion on / OFF, Sensitivity Setting 58 All Motion Setup buttonSize Recording Resolution All Sensors on / OFFRecording Speed 64 Record Size pop-up windowRecording Quality 67 Recording Speed for each channelManual Recording Recording ModeTimer Recording Schedule Recording 108 109 110 By All Set 78 All Set screen112 By Window Set 80 Window Set screen114 82 Each Cell Setup screen By Each Cell116 Recording by Sensor PIR Sensor 84 Sensor window118 IP Mode Network91 IP Mode button GATEWAY, SUBNET, IP Address95 Port Setup window PortDisable / Enable MNS MAC Name ServerIP Address / Port Ddns Dynamic Domain Name SystemUser ID PasswordHost Name HOW to Setup and USE the Ddns 7-7.7.1. Router Registration to the Ddns serverEmail Notification 104 Email Notification windowEmail Address Setup 105 Keyboard window128 129 130 Remote Host Program Deletion of Camera Position Icon Placement of Cameras on the MAPUsage of Camera Position Remote Program Overview Remote system minimum requirementsHow to set Screen Resolution and Color Quality Installing the Program to PCHow to install the program How to setup the Internet Explorer Internet ExplorerClick on the following message Remote Host DVR MasterTable. Description of Remote Host Program Button Setup Host Config window140 141 Connection Capture Connect DialogStatus Mode Status145 Playback control buttons 13 Copy mode Copy148 Switch the Normal Screen to Full Screen 16 Full Screen ButtonSpeaker / Microphone Buttons of Remote Host ProgramConnection mode Terminal modeMulti mode 20 Multi mode screenCopy in the Terminal mode not available on this version 21 Copy Confirmation154 Map Addition of mapPlacement of cameras on the map 27 RenameUsage of camera position Deletion of Camera position iconPan / Tilt & Preset Channel Select PAN / Tilt Focus Zoom Preset / RUNChart. Button of Player Program Player② Calendar It shows the date currently being replayed 161 How to play the AVI files 39 Select one of the Channels163 164 ⑫ Replay Control Refer to section 166 Appendix Recording time table 240fps 120fps 80fps 56fps 24fps 16fpsFactory default settings 169170 171 172 FAQ Please check whether DVR is connected another PC Can not loginPort 5800 on DVR Target Port Number 5800 on Host Program Limited 1Year Warranty How to obtain Factory Service