What to do at the time of Installation | Clover Electronics LCD2084

3. What to do at the time of Installation

The system should be installed in the following order;

1.Make sure all the required hardware is available. -20.1” wide TFT-LCD monitor built-in 8 Ch DVR

-Up to 8 cameras capacity (Refer to the retail box for the number of camera included in the system).

-CCTV monitor or TV set if necessary -Network cable if connecting to a PC

2.Connect the cameras to the monitor (Refer to [Fig. 5-3]).

4.Confirm if live video is displayed on the monitor before going to the next step.

5.Select the Setup Menu and set current date and time (Refer to Section 7-2.3).

6.Run the FACTORY DEFAULT setting in the SYSTEM menu.

7.Perform HDD formatting.

8.Escape from Setup Menu.

9.Set values for required options.

10.Network cable should be connected to the monitor before turning the power on. Refer to [Fig. 5-8]for the cable specification.

15

Image 15

Clover Electronics LCD2084 What to do at the time of Installation, System should be installed in the following order

Contents

Ver , 061009 Wide LCD ScreenPage Contents Video Enhance 100 133 159 Page About this manual Page Unpacking 1 Wide LCD Panel Built-in 8 Ch Digital Video Recorder Multi Functional Record Automatic System RecoveryHigh Resolution DVR 720 x Wide ScreenPage System should be installed in the following order What to do at the time of InstallationPage Specifications Specifications Controls and Connectors Installation Front/Top View Controls and Connectors Enter Key Stand-by Power Mode ButtonRemote Control Signal Receiver REC Key Rear Installation System Connection System Connection Camera Connection Connection of 6pin Mini DIN Cameras InstallationInstallation of the Monitor Installation of the system on the wall Sensor Connection and Relay in &OUT Sensor Connection Sensor Alarm OUT Connection RS485 Connection 4. RS485 Connection 10 Power cable connection Power Cable Connection How to operate Playback Devices SET the Start Time General Information Operating Interface IR Remote Controller STAND-BY Power Mode Button Power On/Off By clicking the mouse Power button on Menu window Menu Window Menu Window Full Screen Display Screen Split Screens Full Screen Sequencing Screen Quad Screen Split Screen Live Sequencing screen Sequencing Screens Audio on , Audio OFF Live Audio Communication Between Monitor and Cameras 11 Zoomed screen Zoom OSD on / OFF OSD on /OFF is possible in the Live mode or Record mode 14 PAN/TILT button PAN / Tilt Iris Channel Selection and Screen ConversionZoom / Focus PAN / Tilt Preset Preset SetupPreset Execution 18 System Status button System Status Power Loss Lists Power Loss Lists 21 Power Loss Lists Message 22 Video Loss Lists window Video Loss List 24 Video Loss Lists Message window Video Enhance 27 Camera Input Camera Input Config Contrast / Brightness VGA Output Config Scale / Contrast / Brightness / Saturation Record Manual Continuous recordingManual Event Recording 30 should be turned on Timer Recording 32 Timer Event Recording setup Timer Event Recording Estimated Recording Time Audio Recording 37 Recording Icons Recording Icons Replay Quick ReplayReplay Set the Start Time Playback Devices By using the Replay Time set-up bar By using the Replay Time set-up buttonsPage ② Play / Pause ③ REW/FF④ Prev / Next Disappearance of Replay control buttons 45 Split screen during replaying Copying devices Copy Set the Copy Start Time Copying extent Regards to blank Medias CD-R/W and DVD-R/W 49 Copy Start time and Channel Selection window By using the Copy Start/End set-up buttons Set the Copy End Time Copying extent By using the Start/End set-up bar Set the ending time and date to copy as described above Copying the recorded data during replaying DVD-RW Copy Select Copy ModeUSB Copy CD-RW Copy 54 Copying Icon Copying the AVI File Format Factory Default Load Config / Backup Config Setup Manual Event Recording Timer Recording Schedule RecordingTimer Event Recording Manual Recording Setup Setup Icon on Menu window Setup System System name button System Name Language Time / DateTime Format Display Date Format System Config 14 Factory Default button Factory Default Load Config Load Config / Backup Config 18 Backup Config button Backup Config Password Password ChangeON/OFF 21 IR Remote ID button IR Remote ID System Info Firmware UpdateBy USB memory By DvrMaster GUI Disk Manager HDD Write Fail HDD OverwriteFormat Camera Camera Name Camera Title Camera ON/OFF Relay Buzzer 35 PAN/TILT button Pan/Tilt Settings 37 PAN/TILT 41 Baudrate button PTZ ID Parity Bit Sequencing dwell time Display Audio Microphone Volume Record Icon Display Record 56 All Manual / Timer button All Manual / Timer recording button 58 All Motion Setup button All Motion on / OFF, Sensitivity Setting All Sensors on / OFF Size Recording Resolution 64 Record Size pop-up window Recording Speed 67 Recording Speed for each channel Recording Quality Recording Mode Timer Recording Schedule RecordingManual Recording 108 109 110 78 All Set screen By All Set 112 80 Window Set screen By Window Set 114 By Each Cell 82 Each Cell Setup screen 116 84 Sensor window Recording by Sensor PIR Sensor 118 Network IP Mode GATEWAY, SUBNET, IP Address 91 IP Mode button Port 95 Port Setup window MNS MAC Name Server Disable / Enable Ddns Dynamic Domain Name System IP Address / Port Password Host NameUser ID Registration to the Ddns server HOW to Setup and USE the Ddns 7-7.7.1. Router 104 Email Notification window Email Notification 105 Keyboard window Email Address Setup 128 129 130 Remote Host Program Placement of Cameras on the MAP Usage of Camera PositionDeletion of Camera Position Icon Remote system minimum requirements Remote Program Overview Installing the Program to PC How to install the programHow to set Screen Resolution and Color Quality Internet Explorer How to setup the Internet Explorer Click on the following message DVR Master Remote Host Table. Description of Remote Host Program Button Host Config window Setup 140 141 Connection Connect Dialog Capture Status Status Mode 145 Playback control buttons Copy 13 Copy mode 148 16 Full Screen Button Switch the Normal Screen to Full Screen Buttons of Remote Host Program Speaker / Microphone Terminal mode Connection mode 20 Multi mode screen Multi mode 21 Copy Confirmation Copy in the Terminal mode not available on this version 154 Addition of map Map 27 Rename Placement of cameras on the map Deletion of Camera position icon Usage of camera position Channel Select PAN / Tilt Focus Zoom Preset / RUN Pan / Tilt & Preset Player Chart. Button of Player Program ② Calendar It shows the date currently being replayed 161 39 Select one of the Channels How to play the AVI files 163 164 ⑫ Replay Control Refer to section 166 Appendix 240fps 120fps 80fps 56fps 24fps 16fps Recording time table 169 Factory default settings 170 171 172 FAQ Can not login Port 5800 on DVR Target Port Number 5800 on Host ProgramPlease check whether DVR is connected another PC Limited 1Year Warranty How to obtain Factory Service