Power Cable Connection | Clover Electronics LCD2088, LCD2084

Stand-alone DVR Instruction Manual

5-4.6. POWER CABLE CONNECTION

Connect the provided AC power cable to the monitor and an AC outlet. AC input voltage is AC 110V to 220V 50/60Hz.

It should not be shared with other electrical equipment on the same line.

Frequent power cuts can cause crucial failures, so if you have an unstable power source we recommend the use of an Uninterrupted Power Supply or other backup power source.

POWER INPUT

[Fig. 5-10 Power cable connection]

28

Image 28

Clover Electronics LCD2088, LCD2084 instruction manual Power Cable Connection, Power cable connection

Contents

Wide LCD Screen Ver , 061009Page Contents Video Enhance 100 133 159 Page About this manual Page Unpacking 1 Wide LCD Panel Built-in 8 Ch Digital Video Recorder Automatic System Recovery High Resolution DVR 720 xWide Screen Multi Functional RecordPage What to do at the time of Installation System should be installed in the following orderPage Specifications Specifications Installation Controls and Connectors Controls and Connectors Front/Top View Stand-by Power Mode Button Remote Control Signal ReceiverREC Key Enter Key Rear Installation System Connection System Connection Installation Installation of the MonitorInstallation of the system on the wall Camera Connection Connection of 6pin Mini DIN Cameras Alarm OUT Connection Sensor Connection and Relay in &OUT Sensor Connection Sensor 4. RS485 Connection RS485 Connection Power Cable Connection 10 Power cable connection How to operate Playback Devices SET the Start Time General Information Operating Interface IR Remote Controller Power On/Off STAND-BY Power Mode Button Power button on Menu window By clicking the mouse Menu Window Menu Window Display Screen Full Screen Split Screens Full Screen Sequencing Screen Quad Screen Live Split Screen Sequencing Screens Sequencing screen Live Audio Audio on , Audio OFF Communication Between Monitor and Cameras Zoom 11 Zoomed screen OSD on /OFF is possible in the Live mode or Record mode OSD on / OFF PAN / Tilt 14 PAN/TILT button Channel Selection and Screen Conversion Zoom / FocusPAN / Tilt Iris Preset Setup PresetPreset Execution System Status 18 System Status button Power Loss Lists Power Loss Lists 21 Power Loss Lists Message Video Loss List 22 Video Loss Lists window 24 Video Loss Lists Message window Video Enhance Camera Input Config Contrast / Brightness 27 Camera Input VGA Output Config Scale / Contrast / Brightness / Saturation Manual Continuous recording RecordManual Event Recording Timer Recording 30 should be turned on Timer Event Recording 32 Timer Event Recording setup Audio Recording Estimated Recording Time Recording Icons 37 Recording Icons Quick Replay ReplayReplay Playback Devices Set the Start Time By using the Replay Time set-up buttons By using the Replay Time set-up barPage ③ REW/FF ② Play / Pause④ Prev / Next Disappearance of Replay control buttons 45 Split screen during replaying Copy Copying devices Regards to blank Medias CD-R/W and DVD-R/W Set the Copy Start Time Copying extent By using the Copy Start/End set-up buttons 49 Copy Start time and Channel Selection window By using the Start/End set-up bar Set the Copy End Time Copying extent Copying the recorded data during replaying Set the ending time and date to copy as described above Select Copy Mode USB CopyCD-RW Copy DVD-RW Copy Copying the AVI File Format 54 Copying Icon Setup Factory Default Load Config / Backup Config Timer Recording Schedule Recording Timer Event RecordingManual Recording Manual Event Recording Setup Setup Setup Icon on Menu window System System Name System name button Time / Date LanguageTime Format Date Format Display System Config Factory Default 14 Factory Default button Load Config / Backup Config Load Config Backup Config 18 Backup Config button Password Change PasswordON/OFF IR Remote ID 21 IR Remote ID button Firmware Update By USB memoryBy DvrMaster GUI System Info Disk Manager HDD Overwrite HDD Write FailFormat Camera Camera ON/OFF Camera Name Camera Title Buzzer Relay Pan/Tilt Settings 35 PAN/TILT button 37 PAN/TILT 41 Baudrate button Parity Bit PTZ ID Display Sequencing dwell time Microphone Volume Audio Record Record Icon Display All Manual / Timer recording button 56 All Manual / Timer button All Motion on / OFF, Sensitivity Setting 58 All Motion Setup button Size Recording Resolution All Sensors on / OFF Recording Speed 64 Record Size pop-up window Recording Quality 67 Recording Speed for each channel Timer Recording Schedule Recording Recording ModeManual Recording 108 109 110 By All Set 78 All Set screen 112 By Window Set 80 Window Set screen 114 82 Each Cell Setup screen By Each Cell 116 Recording by Sensor PIR Sensor 84 Sensor window 118 IP Mode Network 91 IP Mode button GATEWAY, SUBNET, IP Address 95 Port Setup window Port Disable / Enable MNS MAC Name Server IP Address / Port Ddns Dynamic Domain Name System Host Name PasswordUser ID HOW to Setup and USE the Ddns 7-7.7.1. Router Registration to the Ddns server Email Notification 104 Email Notification window Email Address Setup 105 Keyboard window 128 129 130 Remote Host Program Usage of Camera Position Placement of Cameras on the MAPDeletion of Camera Position Icon Remote Program Overview Remote system minimum requirements How to install the program Installing the Program to PCHow to set Screen Resolution and Color Quality How to setup the Internet Explorer Internet Explorer Click on the following message Remote Host DVR Master Table. Description of Remote Host Program Button Setup Host Config window 140 141 Connection Capture Connect Dialog Status Mode Status 145 Playback control buttons 13 Copy mode Copy 148 Switch the Normal Screen to Full Screen 16 Full Screen Button Speaker / Microphone Buttons of Remote Host Program Connection mode Terminal mode Multi mode 20 Multi mode screen Copy in the Terminal mode not available on this version 21 Copy Confirmation 154 Map Addition of map Placement of cameras on the map 27 Rename Usage of camera position Deletion of Camera position icon Pan / Tilt & Preset Channel Select PAN / Tilt Focus Zoom Preset / RUN Chart. Button of Player Program Player ② Calendar It shows the date currently being replayed 161 How to play the AVI files 39 Select one of the Channels 163 164 ⑫ Replay Control Refer to section 166 Appendix Recording time table 240fps 120fps 80fps 56fps 24fps 16fps Factory default settings 169 170 171 172 FAQ Port 5800 on DVR Target Port Number 5800 on Host Program Can not loginPlease check whether DVR is connected another PC Limited 1Year Warranty How to obtain Factory Service