Seagate ST380215SCE, ST3160215SCE, ST3160215ACE DB35.3 Series SATA/PATA Product Manual, Rev. F

Page 11

Drive specification	ST3160215SCE,	ST380215SCE,
	ST3160215ACE	ST380215ACE

Drive acoustics, sound power
Idle**	2.6 bels (typical)
	2.8 bels (max)
CE seek profile	2.7 bels (typical)
	2.8 bels (max)

Nonrecoverable read errors	1 per 1014 bits read
Annualized Failure Rate (AFR)***	0.68%

Warranty	5 years on distribution units.
	To determine the warranty for a specific drive, use a web browser to access
	the following web page: www.seagate.com/support/service/
	From this page, click on the “Verify Your Warranty” link. You will be asked to
	provide the drive serial number, model number (or part number) and country
	of purchase. The system will display the warranty information for your drive.

Contact start-stop cycles (25°C, 50% rel. humidity)	50,000

Supports Hotplug operation per Serial ATA Revision	Yes

2.5specification

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

DB35.3 Series SATA/PATA Product Manual, Rev. F

5

Image 11

Contents

ST3160215SCEST3160215ACE ST380215SCEST380215ACE DB35.3 Series 80-160GBPage Contents DB35.3 Series SATA/PATA Product Manual, Rev. F List of Figures DB35.3 Series SATA/PATA Product Manual, Rev. F Pata models Introduction Sata models About the Serial ATA interface Specification summary table Drive specificationsDrive specifications summary for 160 and 80 Gbyte models DB35.3 Series SATA/PATA Product Manual, Rev. F Recording and interface technology LBA modeDefault logical geometry Formatted capacityStart/stop times Physical characteristicsDrive specification Seek timeSeek mode Power specificationsPower consumption Spinup powerVoltage tolerance Representative current profileConducted noise Sleep mode Power-management modesActive mode Idle modeHumidity Relative humidity Environmental specifications Case temperatureTemperature gradient Wet bulb temperatureFluid Dynamic Bearing FDB motor acoustics Operating vibrationNonoperating vibration AcousticsPerformance Reference Test Description Level Standard Electromagnetic immunityReliability Radio frequency environmentsAgency certification Page China Restriction of Hazardous Substances RoHS Directive Environmental protectionCorrosive environment超出 Handling and static discharge precautions Handling, mounting and configuring the driveMounting the drive Breather filter hole location Breather filter hole precautionsHow to connect the Sata cables How to configure and attach Serial ATA Sata drivesHow to configure the drive How to use the cable-select option How to configure and attach the Parrallel ATA Pata drivesHow to set the jumper settings How to configure the drive as a master or slaveUltra ATA/100 cable Ultra ATA cable connectorsRefer to InterfaceInterface Pin Function Definition Serial ATA connector pin definitionsSignal Serial ATA Sata interfacePage Parallel ATA Pata Interface ATA interface signals and connector pinsCommand name Command code in hex Supported ATA commandsSupported ATA commands Sata only F9HWord Description Value Identify Device commandXx07H Bit Word 93 Pata only Description if bit is set to Bit WordBit Word 0CH Set Features commandCode in features Register A.R.T. command S.M.A.R.T. commandsDB35.3 Series SATA/PATA Product Manual, Rev. F Technical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index Page Sata DB35.3 Series SATA/PATA Product Manual, Rev. F Page Seagate Technology LLC