Seagate ST380215SCE, ST3160215SCE, ST3160215ACE, ST380215ACE Introduction, Sata models, Pata models

Page 7

1.0Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate® DB35.3® Series SATA/PATA model drives:

SATA models

PATA models

ST3160215SCE ST3160215ACE

ST380215SCEST380215ACE

The drives provide the following key features:

•7,200-RPM spindle speed.

•Tunneling Magnetoresistive (TMR) recording heads.

•Low profile deck design for improved air-flow and low-profile system design.

•State-of-the-art cache and on-the-fly error-correction algorithms.

•Full-track multiple-sector transfer capability without local processor intervention.

•Quiet operation.

•SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

•Support for S.M.A.R.T. drive monitoring and reporting.

SATA specific key features:

•High instantaneous (burst) data-transfer rates (up to 300 Mbytes per second).

•Native Command Queueing with command ordering to increase performance in demanding applications.

•Supports latching SATA cables and connectors.

PATA specific key features:

•High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.

•Support for Read Multiple and Write Multiple commands.

•Support for autodetection of master/slave drives that use cable select (CSEL).

DB35.3 Series SATA/PATA Product Manual, Rev. F

1

Image 7

Contents

ST3160215SCEST3160215ACE ST380215SCEST380215ACE DB35.3 Series 80-160GBPage Contents DB35.3 Series SATA/PATA Product Manual, Rev. F List of Figures DB35.3 Series SATA/PATA Product Manual, Rev. F Sata models IntroductionPata models About the Serial ATA interface Specification summary table Drive specificationsDrive specifications summary for 160 and 80 Gbyte models DB35.3 Series SATA/PATA Product Manual, Rev. F Recording and interface technology LBA modeDefault logical geometry Formatted capacityStart/stop times Physical characteristicsDrive specification Seek timeSeek mode Power specificationsPower consumption Spinup powerConducted noise Representative current profileVoltage tolerance Sleep mode Power-management modesActive mode Idle modeHumidity Relative humidity Environmental specifications Case temperatureTemperature gradient Wet bulb temperatureFluid Dynamic Bearing FDB motor acoustics Operating vibrationNonoperating vibration AcousticsPerformance Reference Test Description Level Standard Electromagnetic immunityReliability Radio frequency environmentsAgency certification Page Corrosive environment超出 Environmental protectionChina Restriction of Hazardous Substances RoHS Directive Handling and static discharge precautions Handling, mounting and configuring the driveMounting the drive Breather filter hole location Breather filter hole precautionsHow to configure the drive How to configure and attach Serial ATA Sata drivesHow to connect the Sata cables How to use the cable-select option How to configure and attach the Parrallel ATA Pata drivesHow to set the jumper settings How to configure the drive as a master or slaveUltra ATA/100 cable Ultra ATA cable connectorsInterface InterfaceRefer to Pin Function Definition Serial ATA connector pin definitionsSignal Serial ATA Sata interfacePage Parallel ATA Pata Interface ATA interface signals and connector pinsSupported ATA commands Supported ATA commandsCommand name Command code in hex Sata only F9HWord Description Value Identify Device commandXx07H Bit Word Description if bit is set to Bit WordBit Word 93 Pata only 0CH Set Features commandCode in features Register A.R.T. command S.M.A.R.T. commandsDB35.3 Series SATA/PATA Product Manual, Rev. F Technical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index Page Sata DB35.3 Series SATA/PATA Product Manual, Rev. F Page Seagate Technology LLC