Seagate ST33000651SS Drive Self Test DST, DST failure definition, Implementation, Invoking DST

Page 26

6.2.6Drive Self Test (DST)

Drive Self Test (DST) is a technology designed to recognize drive fault conditions that qualify the drive as a failed unit. DST validates the functionality of the drive at a system level.

There are two test coverage options implemented in DST:

1.Extended test

2.Short test

The most thorough option is the extended test that performs various tests on the drive and scans every logical block address (LBA) of the drive. The short test is time-restricted and limited in length—it does not scan the entire media surface, but does some fundamental tests and scans portions of the media.

If DST encounters an error during either of these tests, it reports a fault condition. If the drive fails the test, remove it from service and return it to Seagate for service.

6.2.6.1DST failure definition

The drive will present a “diagnostic failed” condition through the self-tests results value of the diagnostic log page if a functional failure is encountered during DST. The channel and servo parameters are not modified to test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number of retries required to recover the data.

The following conditions are considered DST failure conditions:

•Seek error after retries are exhausted

•Track-follow error after retries are exhausted

•Read error after retries are exhausted

•Write error after retries are exhausted

Recovered errors will not be reported as diagnostic failures.

6.2.6.2Implementation

This section provides all of the information necessary to implement the DST function on this drive.

6.2.6.2.1State of the drive prior to testing

The drive must be in a ready state before issuing the Send Diagnostic command. There are multiple reasons why a drive may not be ready, some of which are valid conditions, and not errors. For example, a drive may be in process of doing a format, or another DST. It is the responsibility of the host application to determine the “not ready” cause.

While not technically part of DST, a Not Ready condition also qualifies the drive to be returned to Seagate as a failed drive.

A Drive Not Ready condition is reported by the drive under the following conditions:

•Motor will not spin

•Motor will not lock to speed

•Servo will not lock on track

•Drive cannot read configuration tables from the disk

In these conditions, the drive responds to a Test Unit Ready command with an 02/04/00 or 02/04/03 code.

6.2.6.2.2Invoking DST

To invoke DST, submit the Send Diagnostic command with the appropriate Function Code (001b for the short test or 010b for the extended test) in bytes 1, bits 5, 6, and 7.

18

Constellation ES.2 SAS Product Manual, Rev. D

Page 25 Page 27
Image 26
Page 25 Page 27
Contents SED Fips 140-2 Model Review Pending ST33000652SS ST33000650SSST33000651SSStandard Model Self-Encrypting Drive Model Revision history Contents About Fips About self-encrypting drives Defect and error managementInstallation Interface requirementsPage Constellation ES.2 SAS Product Manual, Rev. D List of Figures Constellation ES.2 SAS Product Manual, Rev. D Seagate Technology support services Seagate Online Support and ServicesScope Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean KCCEuropean Union Restriction of Hazardous Substances RoHS Reference documents Self-Encrypting Drives Reference ManualGeneral description Performance Standard featuresMedia description Formatted capacities Factory-installed optionsReliability Programmable drive capacitySeek performance characteristics Performance characteristicsInternal drive characteristics Access timeGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operationRecoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures DST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesStorage Product warrantyShipping Product repair and return informationPowerChoice modes Physical/electrical specificationsPowerChoiceTM power management AC power requirements DC power requirementsPage Conducted noise immunity General DC power requirement notesPower sequencing Current profiles TB model current profilesPower dissipation 3TB models in 3Gb operation3TB models in 6Gb operation Relative humidity Temperature a. OperatingEnvironmental limits Shock Effective altitude sea level a. OperatingShock and vibration Recommended mounting Acoustics Air cleanlinessVibration a. Operating-normal Corrosive environmentSee Section Constellation ES.2 SAS Product Manual, Rev. D Mechanical specifications Mounting configuration dimensionsLevel 2 security About FipsPurpose About self-encrypting drives Controlled accessAdmin SP Data encryptionDrive locking Default passwordRandom number generator RNG Data bandsSupported commands Authenticated firmware downloadPower requirements RevertSPDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Background Media ScanIdle Read After Write Media Pre-ScanDeferred Auto-Reallocation Levels of PI Setting and determining the current Type LevelProtection Information PI Identifying a Protection Information driveInstallation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsSupported commands Supported commands Supported commands Constellation ES.2 inquiry data Mode Sense dataInquiry data Page Mode Sense data changeable and default values for 3TB drives Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutDifferential signals SAS-2 Specification ComplianceLED drive signal General interface characteristicsIndex NumericsKCC Msid Mtbf See also cooling Page Constellation ES.2 SAS Product Manual, Rev. D Page Seagate Technology LLC

ST33000652SS, ST33000650SS, ST33000651SS specifications

The Seagate ST33000651SS, ST33000650SS, and ST33000652SS are high-performance enterprise hard drives designed for demanding storage applications. These models are part of the Seagate Constellation ES series, known for their reliability and performance in server and data center environments.

One of the most notable features of these drives is their capacity. The ST33000651SS and ST33000650SS offer a storage capacity of 3TB, providing ample space for data-intensive applications. The ST33000652SS enhances this with a larger storage option, ensuring that organizations can meet growing data demands without needing frequent upgrades.

These drives utilize a SATA 6Gb/s interface, which allows for high-speed data transfer. This increased bandwidth is essential for applications that rely on rapid access, such as virtualization, cloud computing, and database management systems. Additionally, the drives support Native Command Queuing (NCQ), which enhances performance by optimizing the order in which read and write commands are executed.

Reliability is paramount in enterprise environments, and Seagate addresses this with several technologies designed to minimize downtime. The ST33000651SS and its counterparts feature a 7200 RPM spindle speed, which not only delivers fast access times but also contributes to the overall durability of the drives. They also come with advanced error correction and data integrity features, which safeguard against data loss.

Another important characteristic of these drives is their low power consumption. Operating at an average power usage of 6.0W, they help reduce operational costs, particularly in large-scale deployments. This energy efficiency is essential for organizations looking to maintain sustainability while maximizing performance.

In terms of physical design, these hard drives are built to endure tough conditions typically found in data centers. They come in a standard 3.5-inch form factor, ensuring compatibility with a wide range of servers and storage enclosures. The robust design further enhances their lifespan, making them a sound investment for enterprise storage solutions.

In summary, the Seagate ST33000651SS, ST33000650SS, and ST33000652SS hard drives offer a compelling combination of high capacity, fast data transfer rates, and reliability. Their advanced technologies and energy-efficient design make them ideal choices for enterprises that require dependable and high-performing storage solutions in their IT infrastructure.
Top Page Image Contents