Seagate ST33000651SS, ST33000652SS General DC power requirement notes, Conducted noise immunity

Page 32

[5]See +12V current profile in Figure 1.

[6]This condition occurs after OOB and Speed Negotiation completes but before the drive has received the Notify Spinup primitive.

[7]See paragraph 7.3.1, "Conducted noise immunity." Specified voltage tolerance includes ripple, noise, and transient response.

[8]Operating condition is defined as random 8 block reads.

[9]During idle, the drive heads are relocated every 60 seconds to a random location within the band from three-quarters to maximum track.

General DC power requirement notes.

1.Minimum current loading for each supply voltage is not less than 1.7% of the maximum operating current shown.

2.The +5V and +12V supplies should employ separate ground returns.

3.Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device.

4.Parameters, other than spindle start, are measured after a 10-minute warm up.

5.No terminator power.

7.3.1Conducted noise immunity

Noise is specified as a periodic and random distribution of frequencies covering a band from DC to 10 MHz. Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power connector.

+5v

=

250 mV pp from 100 Hz to 20 MHz.

+12v

=

800 mV pp from 100 Hz to 8 KHz.

 

 

450 mV pp from 8 KHz to 20 KHz.

 

 

250 mV pp from 20 KHz to 5 MHz.

7.3.2Power sequencing

The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down.

24

Constellation ES.2 SAS Product Manual, Rev. D

Page 31 Page 33
Image 32
Page 31 Page 33
Contents SED Fips 140-2 Model Review Pending ST33000652SS ST33000650SSST33000651SSStandard Model Self-Encrypting Drive Model Revision history Contents Defect and error management InstallationAbout Fips About self-encrypting drives Interface requirementsPage Constellation ES.2 SAS Product Manual, Rev. D List of Figures Constellation ES.2 SAS Product Manual, Rev. D Seagate Technology support services Seagate Online Support and ServicesScope Applicable standards and reference documentation StandardsElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance Electromagnetic compliance for the European UnionAustralian C-Tick Korean KCCEuropean Union Restriction of Hazardous Substances RoHS Reference documents Self-Encrypting Drives Reference ManualGeneral description Performance Standard featuresMedia description Factory-installed options ReliabilityFormatted capacities Programmable drive capacityPerformance characteristics Internal drive characteristicsSeek performance characteristics Access timeGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operationReliability specifications Error ratesRecoverable Errors Unrecoverable ErrorsReliability and service Seek errorsInterface errors Preventive maintenance4 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Reporting controlThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures State of the drive prior to testing Drive Self Test DSTDST failure definition ImplementationShort and extended tests Short test Function Code 001bExtended test Function Code 010b Log page entriesProduct warranty ShippingStorage Product repair and return informationPowerChoice modes Physical/electrical specificationsPowerChoiceTM power management AC power requirements DC power requirementsPage Conducted noise immunity General DC power requirement notesPower sequencing Current profiles TB model current profilesPower dissipation 3TB models in 3Gb operation3TB models in 6Gb operation Relative humidity Temperature a. OperatingEnvironmental limits Shock Effective altitude sea level a. OperatingShock and vibration Recommended mounting Air cleanliness Vibration a. Operating-normalAcoustics Corrosive environmentSee Section Constellation ES.2 SAS Product Manual, Rev. D Mechanical specifications Mounting configuration dimensionsLevel 2 security About FipsPurpose Controlled access Admin SPAbout self-encrypting drives Data encryptionDefault password Random number generator RNGDrive locking Data bandsAuthenticated firmware download Power requirementsSupported commands RevertSPDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Background Media ScanIdle Read After Write Media Pre-ScanDeferred Auto-Reallocation Setting and determining the current Type Level Protection Information PILevels of PI Identifying a Protection Information driveInstallation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsSupported commands Supported commands Supported commands Constellation ES.2 inquiry data Mode Sense dataInquiry data Page Mode Sense data changeable and default values for 3TB drives Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Physical characteristics Connector requirementsElectrical description Pin descriptionsSignal characteristics PowerSAS transmitters and receivers Ready LED OutSAS-2 Specification Compliance LED drive signalDifferential signals General interface characteristicsIndex NumericsKCC Msid Mtbf See also cooling Page Constellation ES.2 SAS Product Manual, Rev. D Page Seagate Technology LLC

ST33000652SS, ST33000650SS, ST33000651SS specifications

The Seagate ST33000651SS, ST33000650SS, and ST33000652SS are high-performance enterprise hard drives designed for demanding storage applications. These models are part of the Seagate Constellation ES series, known for their reliability and performance in server and data center environments.

One of the most notable features of these drives is their capacity. The ST33000651SS and ST33000650SS offer a storage capacity of 3TB, providing ample space for data-intensive applications. The ST33000652SS enhances this with a larger storage option, ensuring that organizations can meet growing data demands without needing frequent upgrades.

These drives utilize a SATA 6Gb/s interface, which allows for high-speed data transfer. This increased bandwidth is essential for applications that rely on rapid access, such as virtualization, cloud computing, and database management systems. Additionally, the drives support Native Command Queuing (NCQ), which enhances performance by optimizing the order in which read and write commands are executed.

Reliability is paramount in enterprise environments, and Seagate addresses this with several technologies designed to minimize downtime. The ST33000651SS and its counterparts feature a 7200 RPM spindle speed, which not only delivers fast access times but also contributes to the overall durability of the drives. They also come with advanced error correction and data integrity features, which safeguard against data loss.

Another important characteristic of these drives is their low power consumption. Operating at an average power usage of 6.0W, they help reduce operational costs, particularly in large-scale deployments. This energy efficiency is essential for organizations looking to maintain sustainability while maximizing performance.

In terms of physical design, these hard drives are built to endure tough conditions typically found in data centers. They come in a standard 3.5-inch form factor, ensuring compatibility with a wide range of servers and storage enclosures. The robust design further enhances their lifespan, making them a sound investment for enterprise storage solutions.

In summary, the Seagate ST33000651SS, ST33000650SS, and ST33000652SS hard drives offer a compelling combination of high capacity, fast data transfer rates, and reliability. Their advanced technologies and energy-efficient design make them ideal choices for enterprises that require dependable and high-performing storage solutions in their IT infrastructure.
Top Page Image Contents