Seagate ST33000650SS Signal characteristics, SAS transmitters and receivers, Power, Ready LED Out

Page 67

12.4.6SAS transmitters and receivers

A typical SAS differential copper transmitter and receiver pair is shown in Figure 13. The receiver is AC coupling to eliminate ground shift noise.

 

TX

Transmitter

Differential

Transfer Medium

100

 

 

TY

Figure 13. SAS transmitters and receivers

.01

.01

RX

Receiver

100

RY

12.4.7Power

The drive receives power (+5 volts and +12 volts) through the SAS device connector.

Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Current to the drive through the long power pins may be limited by the system to reduce inrush current to the drive during hot plugging.

12.5Signal characteristics

This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 11 for signal type and signal name information.

12.5.1Ready LED Out

The Ready LED Out signal is driven by the drive as indicated in Table 12.

Table 12: Ready LED Out conditions

Normal command activity

 

LED status

 

 

 

Ready LED Meaning bit mode page 19h

0

 

1

 

 

 

 

Spun down and no activity

Off

 

Off

 

 

 

 

Spun down and activity (command executing)

On

 

On

 

 

 

 

Spun up and no activity

On

 

Off

 

 

 

 

Spun up and activity (command executing)

Off

 

On

 

 

 

 

Spinning up or down

 

Blinks steadily

 

(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)

 

 

 

Format in progress, each cylinder change

 

Toggles on/off

 

 

 

 

Constellation ES.2 SAS Product Manual, Rev. D

59

Image 67
Contents Standard Model Self-Encrypting Drive Model ST33000650SSST33000651SSSED Fips 140-2 Model Review Pending ST33000652SS Revision history Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPage Constellation ES.2 SAS Product Manual, Rev. D List of Figures Constellation ES.2 SAS Product Manual, Rev. D Seagate Online Support and Services Seagate Technology support servicesScope Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickEuropean Union Restriction of Hazardous Substances RoHS Self-Encrypting Drives Reference Manual Reference documentsGeneral description Media description Standard featuresPerformance Programmable drive capacity Factory-installed optionsReliability Formatted capacitiesAccess time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct repair and return information Product warrantyShipping StoragePowerChoiceTM power management Physical/electrical specificationsPowerChoice modes DC power requirements AC power requirementsPage Power sequencing General DC power requirement notesConducted noise immunity TB model current profiles Current profiles3TB models in 3Gb operation Power dissipation3TB models in 6Gb operation Environmental limits Temperature a. OperatingRelative humidity Shock and vibration Effective altitude sea level a. OperatingShock Recommended mounting Corrosive environment Air cleanlinessVibration a. Operating-normal AcousticsSee Section Constellation ES.2 SAS Product Manual, Rev. D Mounting configuration dimensions Mechanical specificationsPurpose About FipsLevel 2 security Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Default passwordRandom number generator RNG Drive lockingRevertSP Authenticated firmware downloadPower requirements Supported commandsDrive internal defects/errors Defect and error managementDrive error recovery procedures Background Media Scan SAS system errorsDeferred Auto-Reallocation Media Pre-ScanIdle Read After Write Identifying a Protection Information drive Setting and determining the current Type LevelProtection Information PI Levels of PIDrive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Inquiry data Mode Sense dataConstellation ES.2 inquiry data Page Mode Sense data changeable and default values for 3TB drives Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification ComplianceLED drive signal Differential signalsNumerics IndexKCC Msid Mtbf See also cooling Page Constellation ES.2 SAS Product Manual, Rev. D Page Seagate Technology LLC

ST33000652SS, ST33000650SS, ST33000651SS specifications

The Seagate ST33000651SS, ST33000650SS, and ST33000652SS are high-performance enterprise hard drives designed for demanding storage applications. These models are part of the Seagate Constellation ES series, known for their reliability and performance in server and data center environments.

One of the most notable features of these drives is their capacity. The ST33000651SS and ST33000650SS offer a storage capacity of 3TB, providing ample space for data-intensive applications. The ST33000652SS enhances this with a larger storage option, ensuring that organizations can meet growing data demands without needing frequent upgrades.

These drives utilize a SATA 6Gb/s interface, which allows for high-speed data transfer. This increased bandwidth is essential for applications that rely on rapid access, such as virtualization, cloud computing, and database management systems. Additionally, the drives support Native Command Queuing (NCQ), which enhances performance by optimizing the order in which read and write commands are executed.

Reliability is paramount in enterprise environments, and Seagate addresses this with several technologies designed to minimize downtime. The ST33000651SS and its counterparts feature a 7200 RPM spindle speed, which not only delivers fast access times but also contributes to the overall durability of the drives. They also come with advanced error correction and data integrity features, which safeguard against data loss.

Another important characteristic of these drives is their low power consumption. Operating at an average power usage of 6.0W, they help reduce operational costs, particularly in large-scale deployments. This energy efficiency is essential for organizations looking to maintain sustainability while maximizing performance.

In terms of physical design, these hard drives are built to endure tough conditions typically found in data centers. They come in a standard 3.5-inch form factor, ensuring compatibility with a wide range of servers and storage enclosures. The robust design further enhances their lifespan, making them a sound investment for enterprise storage solutions.

In summary, the Seagate ST33000651SS, ST33000650SS, and ST33000652SS hard drives offer a compelling combination of high capacity, fast data transfer rates, and reliability. Their advanced technologies and energy-efficient design make them ideal choices for enterprises that require dependable and high-performing storage solutions in their IT infrastructure.