Seagate ST33000651SS manual Physical/electrical specifications, PowerChoiceTM power management

Page 29

7.0Physical/electrical specifications

This section provides information relating to the physical and electrical characteristics of the drive.

7.1PowerChoiceTM power management

Drives using the load/unload architecture provide programmable power management to tailor systems for performance and greater energy efficiency.

The table below lists the supported PowerChoice modes. The further you go down in the table, the more power savings you get. For example, Idle_B mode results in greater power savings than Idle_A mode. Standby_Z mode results in the greatest power savings.

PowerChoice modes

Mode

Description

 

 

Idle_A

Reduced electronics

 

 

Idle_B

Heads unloaded. Disks spinning at full RPM

 

 

Idle_C

Heads unloaded. Disks spinning at reduced RPM

 

 

Standby_Y

Heads unloaded. Disks spinning at reduced RPM.

 

Recovery requires the NOTIFY (Enable Spinup) command.

 

 

Standby_Z

Heads unloaded. Motor stopped (disks not spinning)

 

Recovery requires the NOTIFY (Enable Spinup) command.

 

 

PowerChoiceTM can be invoked using one of these two methods:

•Power Condition mode page method—Enable and initialize the idle condition timers and/or the standby con- dition timers. The timer values are based on the values set in the Power Condition mode page.

•START STOP UNIT command method—Use the START STOP UNIT command (OPERATION CODE 1Bh). This allows the host to directly transition the drive to any supported PowerChoice mode.

If both the Power Condition mode page and START STOP UNIT command methods are used, the START STOP UNIT command request takes precedence over the Power Condition mode page power control and may disable the idle condition and standby condition timers. The REQUEST SENSE command reports the current PowerChoice state if active and also the method by which the drive entered the PowerChoice state.

When the drive receives a command, all power condition timers are suspended if they were enabled via the Power Condition mode page. Once all outstanding commands are processed, the power condition timers are reinitialized to the values defined in the Power Condition mode page.

Constellation ES.2 SAS Product Manual, Rev. D

21

Page 28 Page 30
Image 29
Page 28 Page 30
Contents SED Fips 140-2 Model Review Pending ST33000652SS ST33000650SSST33000651SSStandard Model Self-Encrypting Drive Model Revision history Contents Installation Defect and error managementAbout Fips About self-encrypting drives Interface requirementsPage Constellation ES.2 SAS Product Manual, Rev. D List of Figures Constellation ES.2 SAS Product Manual, Rev. D Seagate Online Support and Services Seagate Technology support servicesScope Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean KCCEuropean Union Restriction of Hazardous Substances RoHS Self-Encrypting Drives Reference Manual Reference documentsGeneral description Performance Standard featuresMedia description Reliability Factory-installed optionsFormatted capacities Programmable drive capacityInternal drive characteristics Performance characteristicsSeek performance characteristics Access timeStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures Drive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesShipping Product warrantyStorage Product repair and return informationPowerChoice modes Physical/electrical specificationsPowerChoiceTM power management DC power requirements AC power requirementsPage Conducted noise immunity General DC power requirement notesPower sequencing TB model current profiles Current profiles3TB models in 3Gb operation Power dissipation3TB models in 6Gb operation Relative humidity Temperature a. OperatingEnvironmental limits Shock Effective altitude sea level a. OperatingShock and vibration Recommended mounting Vibration a. Operating-normal Air cleanlinessAcoustics Corrosive environmentSee Section Constellation ES.2 SAS Product Manual, Rev. D Mounting configuration dimensions Mechanical specificationsLevel 2 security About FipsPurpose Admin SP Controlled accessAbout self-encrypting drives Data encryptionRandom number generator RNG Default passwordDrive locking Data bandsPower requirements Authenticated firmware downloadSupported commands RevertSPDrive error recovery procedures Defect and error managementDrive internal defects/errors Background Media Scan SAS system errorsIdle Read After Write Media Pre-ScanDeferred Auto-Reallocation Protection Information PI Setting and determining the current Type LevelLevels of PI Identifying a Protection Information driveDrive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Constellation ES.2 inquiry data Mode Sense dataInquiry data Page Mode Sense data changeable and default values for 3TB drives Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutLED drive signal SAS-2 Specification ComplianceDifferential signals General interface characteristicsNumerics IndexKCC Msid Mtbf See also cooling Page Constellation ES.2 SAS Product Manual, Rev. D Page Seagate Technology LLC

ST33000652SS, ST33000650SS, ST33000651SS specifications

The Seagate ST33000651SS, ST33000650SS, and ST33000652SS are high-performance enterprise hard drives designed for demanding storage applications. These models are part of the Seagate Constellation ES series, known for their reliability and performance in server and data center environments.

One of the most notable features of these drives is their capacity. The ST33000651SS and ST33000650SS offer a storage capacity of 3TB, providing ample space for data-intensive applications. The ST33000652SS enhances this with a larger storage option, ensuring that organizations can meet growing data demands without needing frequent upgrades.

These drives utilize a SATA 6Gb/s interface, which allows for high-speed data transfer. This increased bandwidth is essential for applications that rely on rapid access, such as virtualization, cloud computing, and database management systems. Additionally, the drives support Native Command Queuing (NCQ), which enhances performance by optimizing the order in which read and write commands are executed.

Reliability is paramount in enterprise environments, and Seagate addresses this with several technologies designed to minimize downtime. The ST33000651SS and its counterparts feature a 7200 RPM spindle speed, which not only delivers fast access times but also contributes to the overall durability of the drives. They also come with advanced error correction and data integrity features, which safeguard against data loss.

Another important characteristic of these drives is their low power consumption. Operating at an average power usage of 6.0W, they help reduce operational costs, particularly in large-scale deployments. This energy efficiency is essential for organizations looking to maintain sustainability while maximizing performance.

In terms of physical design, these hard drives are built to endure tough conditions typically found in data centers. They come in a standard 3.5-inch form factor, ensuring compatibility with a wide range of servers and storage enclosures. The robust design further enhances their lifespan, making them a sound investment for enterprise storage solutions.

In summary, the Seagate ST33000651SS, ST33000650SS, and ST33000652SS hard drives offer a compelling combination of high capacity, fast data transfer rates, and reliability. Their advanced technologies and energy-efficient design make them ideal choices for enterprises that require dependable and high-performing storage solutions in their IT infrastructure.
Top Page Image Contents