Seagate ST3750840ACE manual Voltage tolerance, Power-management modes, Active mode, Idle mode

Page 19

2.8.3Voltage tolerance

Voltage tolerance (including noise):

5V ± 5%

12V ± 10%

2.8.4Power-management modes

The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes:

Power mode

Heads

Spindle

Buffer

 

 

 

 

Active

Tracking

Rotating

Enabled

 

 

 

 

Idle

Tracking

Rotating

Enabled

 

 

 

 

Standby

Parked

Stopped

Enabled

 

 

 

 

Sleep

Parked

Stopped

Disabled

 

 

 

 

•Active mode

The drive is in Active mode during the read/write and seek operations.

•Idle mode

The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc access is necessary.

•Standby mode

The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive accepts all commands and returns to Active mode any time disc access is necessary.

•Sleep mode

The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and enters Standby mode with all current translation parameters intact.

•Idle and Standby timers

Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disc access is necessary.

DB35.3 Series PATA Product Manual, Rev. B

13

Page 18 Page 20
Image 19
Page 18 Page 20
Contents DB35.3 Series Pata Page Contents DB35.3 Series Pata Product Manual, Rev. B List of Figures DB35.3 Series Pata Product Manual, Rev. B Introduction DB35.3 Series Pata Product Manual, Rev. B Specification summary table Drive specificationsDrive specification ST3750840ACE ST3500830ACE ST3400820ACE DB35.3 Series Pata Product Manual, Rev. B Drive specification ST3320820ACE ST3300820ACE ST3250820ACE DB35.3 Series Pata Product Manual, Rev. B Cylinders Read/write heads Sectors per track 16,383 Default logical geometryLBA mode Formatted capacity750GB 500GB 400GB 320GB 300GB 250GB Physical characteristicsDrive specification Recording and interface technologySeek time Power specificationsStart/stop times DC power requirements Standby modeConducted noise Typical current profileSleep mode Power-management modesActive mode Idle modeEnvironmental specifications 4 Disc models ShockOperating shock Nonoperating shock Disc modelsFluid Dynamic Bearing FDB motor acoustics AcousticsIdle CE seek profile Agency certification Safety certificationElectromagnetic immunity ReliabilityFCC verification Electromagnetic compatibilityKorean RRL Australian C-Tick N176Corrosive environment Environmental protectionEuropean Union Restriction of Hazardous Substances RoHS DB35.3 Series Pata Product Manual, Rev. B Handling and static discharge precautions Configuring and mounting the driveBreather filter hole location Breather filter hole precautionsCable-select option Jumper settingsMaster/slave configuration Drive as master with a non-ATA-compatible slaveUltra ATA/100 cable Drive mountingMounting dimensions-top, side and end view DB35.3 Series Pata Product Manual, Rev. B Pins and supported ATA signals ATA interface signals and connector pinsATA interface Command name Command code in hex Supported ATA commandsF4H Word Description Value Identify Device commandXx07H Bit Word Description if bit is set to Bit Word0CH Set Features commandCode in features Register A.R.T. command 4 S.M.A.R.T. commandsTechnical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index Page TMR DB35.3 Series Pata Product Manual, Rev. B Page Seagate Technology LLC
Related manuals
Manual 52 pages 3.56 Kb
Top Page Image Contents