Seagate ST35000414SS SAS-2 Specification Compliance, Additional information, LED drive signal

Page 76

The Ready LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +3.3 volt supply through an appropriate current limiting resistor. The LED and the current limiting resis- tor are external to the drive. See Table 17 for the output characteristics of the LED drive signals.

Table 17:	LED drive signal

State		Test condition	Output voltage

LED off, high		0 V ≤VOH ≤3.6 V	-100 µA < IOH < 100 µA
LED on, low		IOL = 15 mA	0 ≤VOL ≤0.225 V

10.5.2Differential signals

The drive SAS differential signals comply with the intra-enclosure (internal connector) requirements of the SAS standard.

Table 18 defines the general interface characteristics.

Table 18: General interface characteristics

Characteristic	Units	1.5Gb/s	3.0Gb/s	6.0Gb/s

Bit rate (nominal)	Mbaud	1,500	3,000	6,000

Unit interval (UI)(nominal)	ps	666.6	333.3	166.6

Impedance (nominal, differential )	ohm	100	100	100

Transmitter transients, maximum	V	± 1.2	± 1.2	± 1.2

Receiver transients, maximum	V	± 1.2	± 1.2	± 1.2

10.6SAS-2 Specification Compliance

Seagate SAS-2 drives are entirely compatible with the latest SAS-2 Specification (T10/1760-D) Revision 16.

The most important characteristic of the SAS-2 drive at 6Gb/s is that the receiver is capable of adapting the equalizer to optimize the receive margins. The SAS-2 drive has two types of equalizers:

1.A Decision Feedback Equalizer (DFE) which utilizes the standard SAS-2 training pattern transmitted dur- ing the SNW-3 training gap. The DFE circuit can derive an optimal equalization characteristic to compen- sate for many of the receive losses in the system.

2.A Feed Forward Equalizer (FFE) optimized to provide balanced receive margins over a range of channels bounded by the best and worst case channels as defined by the relevant ANSI standard.

10.7Additional information

Please contact your Seagate representative for SAS electrical details, if required.

For more information about the Phy, Link, Transport, and Applications layers of the SAS interface, refer to the Seagate SAS Interface Manual, part number 100293071.

For more information about the SCSI commands used by Seagate SAS drives, refer to the Seagate SCSI Commands Reference Manual, part number 100293068.

68	ConstellationES Series SAS Product Manual, Rev. D

Image 76

Contents ST32000444SS ST31000424SS ST3500414SS ST32000445SS ST31000425SS ST3500415SSStandard Models Self-Encrypting Drive ModelsRevision history Contents Defect and error management InstallationAbout self-encrypting drives Interface requirementsSeagate Technology support services ConstellationES Series SAS Product Manual, Rev. D List of Figures ST32000444SS & ST32000445SS model current profilesConstellationES Series SAS Product Manual, Rev. D Scope Applicable standards and reference documentation StandardsElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance Electromagnetic compliance for the European UnionAustralian C-Tick Korean KCCReference documents European Union Restriction of Hazardous Substances RoHSGeneral description Standard features Media descriptionPerformance ReliabilityFormatted capacities Programmable drive capacityFactory-installed options Performance characteristics Internal drive characteristicsSeek performance characteristics Access timeGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operationReliability specifications Error ratesRecoverable Errors Unrecoverable ErrorsReliability and service Seek errorsInterface errors Preventive maintenance4 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Reporting controlPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor State of the drive prior to testing Drive Self Test DSTDST failure definition ImplementationShort and extended tests Short test Function Code 001bExtended test Function Code 010b Log page entriesShipping Product warrantyProduct repair and return information PowerChoiceTM power management Physical/electrical specificationsPowerChoice modes AC power requirements DC power requirementsConstellationES Series SAS Product Manual, Rev. D ConstellationES Series SAS Product Manual, Rev. D Page Power sequencing General DC power requirement notesConducted noise immunity Current profiles ST32000444SS & ST32000445SS model current profilesST31000424SS & ST31000425SS model current profiles ST3500414SS & ST3500415SS model current profiles Power dissipation ST32000444SS and ST32000445SS in 3Gb operationST32000444SS and ST32000445SS in 6Gb operation ST31000424SS and ST31000425SS in 3Gb operation ST31000424SS and ST31000425SS in 6Gb operation ST3500414SS and ST3500415SS in 3Gb operation ST3500414SS CURRENT/POWER vs Throughput SAS 3.0GBOs per Second ST3500414SS and ST3500415SS in 6Gb operation Environmental limits Temperature a. OperatingRelative humidity Shock and vibration Effective altitude sea level a. OperatingShock Recommended mounting Air cleanliness Vibration a. Operating-normalAcoustics Corrosive environmentElectromagnetic susceptibility Mechanical specifications Mounting configuration dimensionsControlled access Admin SPAbout self-encrypting drives Data encryptionDefault password Random number generator RNGDrive locking Data bandsAuthenticated firmware download Power requirementsSupported commands Cryptographic eraseDrive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Media Pre-Scan Background Media ScanDeferred Auto-Reallocation Idle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsSupported commands Supported commands Supported commands Inquiry data Mode Sense dataConstellation ES inquiry data Page Mode Data Header 74 70 6d b0 00 00 02 3a 38 60 30 00 00 02 Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Physical characteristics Connector requirementsElectrical description Pin descriptionsSignal characteristics PowerSAS transmitters and receivers Ready LED OutSAS-2 Specification Compliance LED drive signalDifferential signals General interface characteristicsSeagate Technology support services Warranty Support Direct.seagate.com Spp.seagate.comWeb Presales SupportTechnical Support Warranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Presales SupportIndex NumericsKCC Msid Mtbf See also cooling Page ConstellationES Series SAS Product Manual, Rev. D Page Seagate Technology LLC