Seagate ST35000414SS manual Physical/electrical specifications, PowerChoiceTM power management

Page 28

6.0Physical/electrical specifications

This section provides information relating to the physical and electrical characteristics of the drive.

6.1PowerChoiceTM power management

Drives using the load/unload architecture provide programmable power management to tailor systems for per- formance and greater energy efficiency.

The table below lists the supported PowerChoice modes. The further you go down in the table, the more power savings you get. For example, Idle2 mode results in greater power savings than Idle1 mode. Standby mode results in the greatest power savings.

PowerChoice modes

Mode	Description

Idle_A	Reduced electronics

Idle_B	Heads unloaded. Disks spinning at full RPM

Idle_C	Heads unloaded. Disks spinning at reduced RPM

Standby_Y	Heads unloaded. Disks spinning at reduced RPM.
	Recovery requires the NOTIFY (Enable Spinup) command.

Standby_Z	Heads unloaded. Motor stopped (disks not spinning)
	Recovery requires the NOTIFY (Enable Spinup) command.

PowerChoiceTM can be invoked using one of these two methods:

•Power Condition mode page method—Enable and initialize the idle condition timers and/or the standby con- dition timers. The timer values are based on the values set in the Power Condition mode page.

•START STOP UNIT command method—Use the START STOP UNIT command (OPERATION CODE 1Bh). This allows the host to directly transition the drive to any supported PowerChoice mode.

If both the Power Condition mode page and START STOP UNIT command methods are used, the START STOP UNIT command request takes precedence over the Power Condition mode page power control and may disable the idle condition and standby condition timers. The REQUEST SENSE command reports the current PowerChoice state if active and also the method by which the drive entered the PowerChoice state.

When the drive receives a command, all power condition timers are suspended if they were enabled via the Power Condition mode page. Once all outstanding commands are processed, the power condition timers are reinitialized to the values defined in the Power Condition mode page.

20	ConstellationES Series SAS Product Manual, Rev. D

Image 28

Contents ST32000444SS ST31000424SS ST3500414SS ST32000445SS ST31000425SS ST3500415SSStandard Models Self-Encrypting Drive ModelsRevision history Contents Defect and error management InstallationAbout self-encrypting drives Interface requirementsSeagate Technology support services ConstellationES Series SAS Product Manual, Rev. D List of Figures ST32000444SS & ST32000445SS model current profilesConstellationES Series SAS Product Manual, Rev. D Scope Applicable standards and reference documentation StandardsElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance Electromagnetic compliance for the European UnionAustralian C-Tick Korean KCCReference documents European Union Restriction of Hazardous Substances RoHSGeneral description Standard features Media descriptionPerformance ReliabilityFormatted capacities Programmable drive capacityFactory-installed options Performance characteristics Internal drive characteristicsSeek performance characteristics Access timeGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operationReliability specifications Error ratesRecoverable Errors Unrecoverable ErrorsReliability and service Seek errorsInterface errors Preventive maintenance4 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Reporting controlPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor State of the drive prior to testing Drive Self Test DST DST failure definition ImplementationShort and extended tests Short test Function Code 001bExtended test Function Code 010b Log page entriesShipping Product warrantyProduct repair and return information PowerChoiceTM power management Physical/electrical specificationsPowerChoice modes AC power requirements DC power requirementsConstellationES Series SAS Product Manual, Rev. D ConstellationES Series SAS Product Manual, Rev. D Page Power sequencing General DC power requirement notesConducted noise immunity Current profiles ST32000444SS & ST32000445SS model current profilesST31000424SS & ST31000425SS model current profiles ST3500414SS & ST3500415SS model current profiles Power dissipation ST32000444SS and ST32000445SS in 3Gb operationST32000444SS and ST32000445SS in 6Gb operation ST31000424SS and ST31000425SS in 3Gb operation ST31000424SS and ST31000425SS in 6Gb operation ST3500414SS and ST3500415SS in 3Gb operation ST3500414SS CURRENT/POWER vs Throughput SAS 3.0GBOs per Second ST3500414SS and ST3500415SS in 6Gb operation Environmental limits Temperature a. OperatingRelative humidity Shock and vibration Effective altitude sea level a. OperatingShock Recommended mounting Air cleanliness Vibration a. Operating-normalAcoustics Corrosive environmentElectromagnetic susceptibility Mechanical specifications Mounting configuration dimensionsControlled access Admin SPAbout self-encrypting drives Data encryptionDefault password Random number generator RNGDrive locking Data bandsAuthenticated firmware download Power requirementsSupported commands Cryptographic eraseDrive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Media Pre-Scan Background Media ScanDeferred Auto-Reallocation Idle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsSupported commands Supported commands Supported commands Inquiry data Mode Sense dataConstellation ES inquiry data Page Mode Data Header 74 70 6d b0 00 00 02 3a 38 60 30 00 00 02 Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Physical characteristics Connector requirementsElectrical description Pin descriptionsSignal characteristics PowerSAS transmitters and receivers Ready LED OutSAS-2 Specification Compliance LED drive signalDifferential signals General interface characteristicsSeagate Technology support services Warranty Support Direct.seagate.com Spp.seagate.comWeb Presales SupportTechnical Support Warranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Presales SupportIndex NumericsKCC Msid Mtbf See also cooling Page ConstellationES Series SAS Product Manual, Rev. D Page Seagate Technology LLC