Tyan Computer S5520 Table of Contents, Introduction, Board Installation, Bios Setup, Diagnostics

Page 2

Table of Contents

 

Check the box contents!

3

Chapter 1: Introduction

 

1.1

Congratulations

5

1.2

Hardware Specifications

5

Chapter 2: Board Installation

 

2.1

Board Image

8

2.2

Block Diagram

9

2.3

Board Parts, Jumpers and Connectors

10

2.4

Tips on Installing Motherboard in Chassis

20

2.5

Installing the Memory

21

2.6

Installing the Processor and Cooling Fan

23

2.7

Attaching Drive Cables

26

2.8

Installing Add-in Cards

27

2.9

Installing Optional SO-DIMM Modules

28

2.10

Connecting External Devices

29

2.11

Installing the Power Supply

30

2.12

Finishing Up

30

Chapter 3: BIOS Setup

 

3.1

About the BIOS

31

3.2

Main BIOS Setup

33

3.3

Main Menu

34

3.4

Advanced Menu

41

3.5

Security Menu

61

3.6

Power Menu

62

3.7

Boot Menu

63

3.8

Exit Menu

64

Chapter 4: Diagnostics

 

4.1

Beep Codes

65

4.2

Flash Utility

65

4.3

Phoenix BIOS Post Code

66

Appendix: SMDC Information

69

Glossary

71

Technical Support

77

2

Image 2
Contents Toledo q35T S5220 VersionBios Setup Table of ContentsBoard Installation DiagnosticsCheck the box contents Page Congratulations Hardware SpecificationsIntroduction System Management Power SupplyMemory External I/O PortsBoard Installation How to install our products right… the first timeBoard Image Block Diagram Toledo q35T S5220Board Parts, Jumpers and Connectors Jumper LegendFront Panel Connector Jumper/Connector FunctionUSB Front Panel Connector Front Panel Connector for BareboneCPUFAN1 FAN5 FAN2 FAN3 LCM J30 LCM Header for Barebone CPUFAN1/FAN2~FAN6 4-pin Fan Connector with TachometerJ24 Aux. Power Connector for Tyan Riser Card M2061 TYFP1 J37 Front Panel HeaderPage FP-AUDIO J5 Front Panel Audio Connector USB3/USB4/USB5/USB6 USB Front Panel ConnectorSATA1/2/3/4/5/6 Serial ATA Connector COM2 J29 COM2 HeaderJ52 J50 J50/J52/TYFAN J27 Fan Connector for Barebone TYFP2 J28 Front Panel Connector for BareboneTYFP3 J31 Front Panel Connector for Barebone J50/J52Cmos Cmos J14 Clear Cmos Jumper Normal Default Tips on Installing Motherboard in Chassis Installing the Memory Memory Installation Procedure Installing the Processor and Cooling Fan Processor Installation LGA 775 SocketCooling Fan Installation Page Attaching Drive Cables Attaching IDE Drive CableInstalling Add-In Cards Installing Optional SO-DIMM modules Connecting External Devices Onboard LAN LED Color DefinitionFinishing Up Installing the Power SupplyApplying power to the board Starting Setup Bios SetupAbout the Bios Getting Help Case of ProblemsSetup Variations Main Bios Setup Main System Time / Date setupInstalled Memory/Available to OS/Used by devices Legacy Diskette aMulti-Sector Transfers LBA Mode ControlType Bit I/O Transfer ModeUltra DMA Mode Memory Cache Cache System Bios AreaCache Video Bios Area Cache Extended Memory Area Cache Base 0-512KCache Base 512-640K Keyboard Error Report Boot FeaturesHalt on Errors Boot-time Diagnostic ScreenQuickBoot Mode Extended Memory TestingEnables support for legacy USB Options Enabled / Disabled Reset Configuration DataLarge Disk Access Mode AdvancedAdvanced Chipset Control WatchDog ModeWatchdog Timer Enable Multimedia Timer Default Primary Video AdapterDvmt 4.0 Mode Memory ReclaimingSata Ahci Enable Native Mode OperationSata RAID Enable Sata Ahci Legacy EnableUSB Dev #29 Controls Dev #29 Options Fun #0, 1, 2, 7 / Fun#0, 7 / Fun#0, 1, 7 / DisabledIntegrated Device Control Sub-Menu USB Dev #26 Controls Dev #26LAN1 / LAN2 Option ROM Scan Initialize device expansion ROM Options Disabled / EnabledLAN Control Sub-Menu PCI Express Sub-Menu Read onlyPCI-E1 Sub-Menu PCI Express Graphics PortPCI-E2 Sub-Menu PCI Express Port #1This section allows you to fine-tune the processor options Single Logical Proc. ModeAdvanced Processor Options HyperthreadingProcessor Power Management C1 Enhanced ModeNo Execute Mode Mem Protection Peci InterfaceSerial Port A/B Device ConfigurationFloppy disk Controller Base I/O AddressEvent Log Validity DMI Event LoggingEvent Log Capacity View DMI Event LogItems can not be modified in user mode. Read only FAN Fail LED IndicatorHardware Monitor Auto Fan ControlVoltage Monitoring Sub-Menu Ipmi Ipmi Specification Version / BMC Firmware VersionBios Post Errors System Event LoggingTimer for loading OS SEC Bios Post WatchdogOS Boot Watchdog Watch dog timer value Options 10System Event Log list mode Sub-Menu V5VSBRealtime Sensor Data Sub-Menu SystempCom Port Address Flow Control Enables Flow ControlConsole Redirection Baud RateSecurity Power It shows the boot priority for installed devices BootBoot Priority Order Excluded from boot orderExit Flash Utility DiagnosticsBeep Codes Memory, Video, CPUPhoenix Bios Post Code Code Beeps / DescriptionBios shadow Caches 30h Code Beeps / Description Appendix Smdc Information OverviewFeatures of Tyan Server Management How Smdc and TSO WorkGlossary Page Page Mirroring see RAID Page Striping see RAID Technical Support Returning Merchandise for Service Document # D1922-110