Tyan Computer Q35T, S5520 warranty PCI-E2 Sub-Menu, PCI Express Port #1

Page 49

3.4.1.2.2 PCI-E2 Sub-Menu

		PhoenixBIOS Setup Utility
	Main	Advanced	Security	Power	Boot		Exit
		PCI-E2 Sub-Menu			Item Specific Help
					Item Specific Help
PCI-E Port 1			[Auto]		Disabled ---		Port always
-------------------------------------------------------------------------					disabled.
Port #1 Enabled					(If Port #1 is disabled,
Port #1 Number					then the rest of the
Port #1 Width					Ports will also be
--------------------------------------------------------------------------					disabled.)
Port #1 Slot Number					Enabled ---		Port always
Port #1 Power Limit					enabled.
Port #1 Slot Card Detect					Auto ---	Only enable if
					card found.

F1	Help	↑↓ Select Item	-/+Change Values		F9	Setup Defaults
Esc	Exit	← → Select Menu	Enter Select	X Sub-Menu F10 Save and Exit

PCI Express Port #1

This feature is used to control the PCI Express Port #1.

Options: Auto / Enabled / Disabled

Port #1 Enabled / Port #1 Number / Port #1 Width / Port #1 Slot Number / Port #1 Power Limit / Port #1 Slot Card Detect

Read only.

Image 49

Contents Version Toledo q35T S5220Board Installation Table of ContentsBios Setup DiagnosticsCheck the box contents Page Introduction Hardware SpecificationsCongratulations Memory Power SupplySystem Management External I/O PortsHow to install our products right… the first time Board InstallationBoard Image Toledo q35T S5220 Block DiagramJumper Legend Board Parts, Jumpers and ConnectorsUSB Front Panel Connector Jumper/Connector FunctionFront Panel Connector Front Panel Connector for BareboneCPUFAN1 FAN5 FAN2 FAN3 J24 Aux. Power Connector for Tyan Riser Card M2061 CPUFAN1/FAN2~FAN6 4-pin Fan Connector with TachometerLCM J30 LCM Header for Barebone TYFP1 J37 Front Panel HeaderPage SATA1/2/3/4/5/6 Serial ATA Connector USB3/USB4/USB5/USB6 USB Front Panel ConnectorFP-AUDIO J5 Front Panel Audio Connector COM2 J29 COM2 HeaderJ52 J50 TYFP3 J31 Front Panel Connector for Barebone TYFP2 J28 Front Panel Connector for BareboneJ50/J52/TYFAN J27 Fan Connector for Barebone J50/J52Cmos Cmos J14 Clear Cmos Jumper Normal Default Tips on Installing Motherboard in Chassis Installing the Memory Memory Installation Procedure Processor Installation LGA 775 Socket Installing the Processor and Cooling FanCooling Fan Installation Page Attaching IDE Drive Cable Attaching Drive CablesInstalling Add-In Cards Installing Optional SO-DIMM modules Onboard LAN LED Color Definition Connecting External DevicesApplying power to the board Installing the Power SupplyFinishing Up About the Bios Bios SetupStarting Setup Setup Variations Case of ProblemsGetting Help Main Bios Setup Installed Memory/Available to OS/Used by devices System Time / Date setupMain Legacy Diskette aType LBA Mode ControlMulti-Sector Transfers Ultra DMA Mode Transfer ModeBit I/O Cache Video Bios Area Cache System Bios AreaMemory Cache Cache Base 512-640K Cache Base 0-512KCache Extended Memory Area Halt on Errors Boot FeaturesKeyboard Error Report Boot-time Diagnostic ScreenExtended Memory Testing QuickBoot ModeLarge Disk Access Mode Reset Configuration DataEnables support for legacy USB Options Enabled / Disabled AdvancedWatchdog Timer WatchDog ModeAdvanced Chipset Control Dvmt 4.0 Mode Default Primary Video AdapterEnable Multimedia Timer Memory ReclaimingSata RAID Enable Native Mode OperationSata Ahci Enable Sata Ahci Legacy EnableIntegrated Device Control Sub-Menu Options Fun #0, 1, 2, 7 / Fun#0, 7 / Fun#0, 1, 7 / DisabledUSB Dev #29 Controls Dev #29 USB Dev #26 Controls Dev #26LAN Control Sub-Menu Initialize device expansion ROM Options Disabled / EnabledLAN1 / LAN2 Option ROM Scan Read only PCI Express Sub-MenuPCI Express Graphics Port PCI-E1 Sub-MenuPCI Express Port #1 PCI-E2 Sub-MenuAdvanced Processor Options Single Logical Proc. ModeThis section allows you to fine-tune the processor options HyperthreadingNo Execute Mode Mem Protection C1 Enhanced ModeProcessor Power Management Peci InterfaceFloppy disk Controller Device ConfigurationSerial Port A/B Base I/O AddressEvent Log Capacity DMI Event LoggingEvent Log Validity View DMI Event LogHardware Monitor FAN Fail LED IndicatorItems can not be modified in user mode. Read only Auto Fan ControlVoltage Monitoring Sub-Menu Bios Post Errors Ipmi Specification Version / BMC Firmware VersionIpmi System Event LoggingOS Boot Watchdog Bios Post WatchdogTimer for loading OS SEC Watch dog timer value Options 10V5VSB System Event Log list mode Sub-MenuSystemp Realtime Sensor Data Sub-MenuConsole Redirection Flow Control Enables Flow ControlCom Port Address Baud RateSecurity Power Boot Priority Order BootIt shows the boot priority for installed devices Excluded from boot orderExit Beep Codes DiagnosticsFlash Utility Memory, Video, CPUCode Beeps / Description Phoenix Bios Post CodeBios shadow Caches 30h Code Beeps / Description Overview Appendix Smdc InformationHow Smdc and TSO Work Features of Tyan Server ManagementGlossary Page Page Mirroring see RAID Page Striping see RAID Technical Support Returning Merchandise for Service Document # D1922-110