Tyan Computer B2933 manual Bios

Page 11

BIOS			System Cooling
• AMI BIOS on 8Mbit LPC Flash ROM			•	(4) 4028 fans
•	Serial Console Redirect		• (1) passive CPU heatsink
•	USB boot supported
			Power Supply
•	ACPI 2.0 supported
			• EPS 400W, 1U, 12V
• PnP, DMI2.0, WfM2.0 power
				(24pin+8pin+4pin) power
	management
				connectors

System Management
			Regulatory
• SMSC SCH5017 w/ 2xEMC6D103
			• FCC Class B (Declaration of
• 8x4 pin system fan headers with
				Conformity)
	tachometer input and auto fan
			• CE (Declaration of Conformity)
	control

• Temperature and voltage monitoring			Environment Temperature
•	Watch dog timer		•	Operating temperature 5oC~35oC
• Port 80 code display LED			•	Non-operating temperature -40oC ~
Server Management				70oC

•TYAN M3291, IPMI 2.0 (2x25pin) Remote system Mgmt card

•Renesas H8S2167 BMC controller

•BT, KCS, Logging support

•IPMI-over-LAN

•Remote power on/off

•Support TSM and LCM module

Chapter 1: Overview

3

Image 11

Contents Transport GT14 B2933 Service Engineer’s Manual Page Preface Federal Communications Commission FCC About this Manual Safety Information Table of Contents Replacing Pre-Installed Components Product Model About the Transport GT14 B2933Enclosure FeaturesBios Unpacking Rail for 2-post rack Rail for 4-post rackRail for 4-post rack Rear View About the ProductFront View Rear I/O LED LED Definition Front PanelInternal View Socket F MotherboardMotherboard Layout Jumper Function Connector Jumpers & ConnectorsModel Picture Quantity Description Number Standard Parts FRU ListModel Picture Quantity Description Number Model Picture Quantity Description Number Optional Parts Model Picture Quantity Description Tools Before You BeginWork Area Precautions Removing the Top Chassis Cover Installing Motherboard ComponentsInstalling the CPU and Heatsink Setting Up Installing the Memory Setting Up Population order for 64-bit mode is DIMM3 first, then DIMM1 Installing the PCI-E Card Setting Up Installing a 3.5 Hard Drive front location Installing the 3.5 Hard DriveSetting Up Setting Up Installing a 3.5 Hard Drive rear location Setting Up Setting Up Installing a 2.5 Hard Drive front location Installing the 2.5 Hard DriveSetting Up Setting Up Installing a 2.5 Hard Drive rear location Setting Up Connect the Sata drive data and power connectors Installing Dual 2.5 Hard Drives front location Installing Dual 2.5 Hard Drives OptionSetting Up Setting Up Setting Up Setting Up Installing Dual 2.5 Hard Drives rear location Setting Up Setting Up Screws List Rack MountingInstalling the Inner Rails to Chassis Installing the Server in a Rack with Rail kit aSetting Up Installing Outer Rails to the Rack Rackmounting the Server Setting Up Installing the Server in an Open Rack with Rail kit B Setting Up Setting Up Configuring the System LCD Software SetupKey Definition LCD ConsoleDOS Mode DOS Mode and Windows ModeSystem Nics Windows ModeHost Name System Sensors Power CtrlLinux Mode Screen Display Introduction Replacing Pre-Installed ComponentsPrecautions Following flowchart outlines the disassembly procedure Disassembly FlowchartRemoving the Top Chassis Cover Replacing Motherboard Components Disconnecting All Motherboard CablesRemoving the Motherboard Replacing the LCD Module and LED Board Replacing Pre-Installed Components Replacing Pre-Installed Components 2 M1017 LED Board Connector Pin Definition 1 M1017 LED Board FeaturesReplacing the USB Board USB Board Connector Pin Definition USB Board FeaturesReplacing the Cooling Fans Replacing Pre-Installed Components Replacing the Power Supply Replacing Pre-Installed Components S2933 Advanced/Hardware Health Configuration Appendix I Bios DifferencesAdvanced Bios Setup Utility B2933 Advanced/Hardware Health ConfigurationAppendix II Cable Connection Tables Other Cables Appendix III Installing the Smdc Card Cable Connection Table Appendix IV Installing the M2061 Riser Card Page Help Resources Technical SupportReturning Merchandise for Service