Tyan Computer B2933 manual Linux Mode

Page 69

2.7.3 Linux Mode

Linux Mode

Host Name

System Nics

Performance

System Sensors

Power Ctl

NIC0

NIC1

CPU

Memory

Hard Disk

Net Interface

Fan

Voltage

Temperature

Power Down

Reboot

Item

Screen Display

 

 

 

 

 

Host Name

TYAN Computer

 

GT14 B2933

 

 

 

 

 

 

 

 

 

 

 

 

1

 

System Nics

 

 

 

 

 

1.1

NIC0

DHCP

 

 

 

IP Address:

 

 

 

xx.xx.x.xxx

 

 

 

Net Mask:

 

 

 

xxx.xxx.xxx.0

 

 

 

Gateway:

 

 

 

xxx.xxx.xxx.0

 

 

 

 

 

1.2

NIC1

DHCP

 

 

 

IP Address:

 

 

 

xx.xx.x.xxx

 

 

 

Net Mask:

 

 

 

xxx.xxx.xxx.0

 

 

 

Gateway:

 

 

 

xxx.xxx.xxx.0

 

 

 

 

Chapter 2: Setting Up

61

Image 69
Contents Transport GT14 B2933 Service Engineer’s Manual Page Preface Federal Communications Commission FCC About this Manual Safety Information Table of Contents Replacing Pre-Installed Components Product Model About the Transport GT14 B2933Enclosure FeaturesBios Unpacking Rail for 2-post rack Rail for 4-post rackRail for 4-post rack About the Product Front ViewRear View Rear I/O LED LED Definition Front PanelInternal View Socket F MotherboardMotherboard Layout Jumper Function Connector Jumpers & ConnectorsModel Picture Quantity Description Number Standard Parts FRU ListModel Picture Quantity Description Number Model Picture Quantity Description Number Optional Parts Model Picture Quantity Description Before You Begin Work AreaTools Precautions Removing the Top Chassis Cover Installing Motherboard ComponentsInstalling the CPU and Heatsink Setting Up Installing the Memory Setting Up Population order for 64-bit mode is DIMM3 first, then DIMM1 Installing the PCI-E Card Setting Up Installing a 3.5 Hard Drive front location Installing the 3.5 Hard DriveSetting Up Setting Up Installing a 3.5 Hard Drive rear location Setting Up Setting Up Installing a 2.5 Hard Drive front location Installing the 2.5 Hard DriveSetting Up Setting Up Installing a 2.5 Hard Drive rear location Setting Up Connect the Sata drive data and power connectors Installing Dual 2.5 Hard Drives front location Installing Dual 2.5 Hard Drives OptionSetting Up Setting Up Setting Up Setting Up Installing Dual 2.5 Hard Drives rear location Setting Up Setting Up Screws List Rack MountingInstalling the Inner Rails to Chassis Installing the Server in a Rack with Rail kit aSetting Up Installing Outer Rails to the Rack Rackmounting the Server Setting Up Installing the Server in an Open Rack with Rail kit B Setting Up Setting Up Configuring the System LCD Software SetupKey Definition LCD Console DOS Mode DOS Mode and Windows ModeWindows Mode Host NameSystem Nics System Sensors Power CtrlLinux Mode Screen Display Introduction Replacing Pre-Installed ComponentsPrecautions Following flowchart outlines the disassembly procedure Disassembly FlowchartRemoving the Top Chassis Cover Replacing Motherboard Components Disconnecting All Motherboard CablesRemoving the Motherboard Replacing the LCD Module and LED Board Replacing Pre-Installed Components Replacing Pre-Installed Components 2 M1017 LED Board Connector Pin Definition 1 M1017 LED Board FeaturesReplacing the USB Board USB Board Connector Pin Definition USB Board FeaturesReplacing the Cooling Fans Replacing Pre-Installed Components Replacing the Power Supply Replacing Pre-Installed Components S2933 Advanced/Hardware Health Configuration Appendix I Bios DifferencesAdvanced Bios Setup Utility B2933 Advanced/Hardware Health ConfigurationAppendix II Cable Connection Tables Other Cables Appendix III Installing the Smdc Card Cable Connection Table Appendix IV Installing the M2061 Riser Card Page Help Resources Technical SupportReturning Merchandise for Service