Tyan Computer S2877 warranty Thermal Interface Material

Page 24

2.6 - Thermal Interface Material

There are two types of thermal interface materials designed for use with the AMD Opteron processor.

The most common material comes as a small pad attached to the heatsink at the time of purchase. There should be a protective cover over the material. Take care not to touch this material. Simply remove the protective cover and place the heatsink on the processor.

The second type of interface material is usually packaged separately. It is commonly referred to as ‘thermal compound’. Simply apply a thin layer on to the CPU lid (applying too much will actually reduce the cooling).

NOTE

Always check with the manufacturer of the heatsink & processor to ensure the Thermal Interface material is compatible with the processor & meets the manufacturer’s warranty requirements

24

http://www.tyan.com

Image 24
Contents Copyright TrademarkVersion Table of Contents Introduction Board InstallationBios Page Hardware Specifications CongratulationsIntegrated FireWire Ieee 1394A Controller Anrf version only Expansion SlotsIntegrated I/O Ports Back Panel I/O PortsSoftware Specifications OS Operating System SupportPage Board Installation Board Image Block Diagram Tiger K8WE S2877 Block DiagramBoard Parts, Jumpers and Connectors Jumper/Connector Function Settings Jumper LegendDefault Front Panel Header J139 FunctionClear Cmos Header J112 4 *FireWire IEEE1394A Enable/Disable Jumper *J147 Chassis Intrusion Header J77Pin-2 Pin-15 *FireWire IEEE1394A Pin Header *J148/*J149 Buzzer/External Speaker Header J14Open Pin3 and Pin4 7 COM2 Connector J42 USB 2.0 Front Panel Headers J25/J140Keyboard Lock Connector J13 Open ClosedGigabit LAN1/**LAN2 Front Panel Header J2/ **J3 S2877G2NR version11 **VGA ATI Rage XL Enable/ Disable Jumper **J85 CPU FAN Connector J9/J37 13 *Front Panel Audio Header *P53Chassis 4-pin FAN Connector J47 Chassis 3-pin FAN Connectors J36/J1017 3-pin or 4-pin fan support selection jumper J5 CPU1 FAN CPU2 FANInstalling the Processors Heatsink Retention Frame Installation Thermal Interface Material Heatsink Installation Procedures Type a CAM Lever Type InstallationType B Screw Retention Type Heatsink Finishing Installing the Heatsink Tips on Installing Motherboard in Chassis Installing the Memory CPU1 CPU2 DIMM-A1 DIMM-A2 DIMM-B1 DIMM-B2 Memory Installation Procedure Attaching Drive Cables Attaching IDE Drive CablePage Installing Add-In Cards Connecting External Devices Onboard LAN LED Color DefinitionInstalling the Power Supply Tips on modifying I/O shielding for Anrf and G2NR versionApplying power to the board Finishing UpPage Bios Setup Utility To select an itemBios Menu Bar Bios Legend BarGetting Help Bios Main Menu Feature Option DescriptionBios Advanced Menu Menu ItemHammer Configuration Sub-Menu Disabled Integrated Devices Sub-MenuAuto LimitFeature Option Description Disabled EnabledNV Configuration PCI Configuration Sub-Menu PCI Device, Slot # 1 ,2,3 Onboard Device Control Add OnPCI/PNP ISA UHB Region Exclusion AvailableFeature Option Description Available PCI/PNP ISA IRQ Resource ExclusionIDE Configuration Sub-Menu OtherBoth Primary Master/Slave, Secondary Master/Slave StandardFloppy Configuration Sub-Menu 6 I/O Device Configuration Sub-Menu 3F8Normal Hardware Monitor Sub-Menu 378Output only PrimaryConsole Redirection Sub-Menu 1920038400 57600 115200 VT100Watchdog Timer Option Sub-Menu Direct~255 Bios Memory Menu MemorySecurity Menu UshcBios Boot Menu UserBoot Device Priority ALL PCI ScsiPower Menu EnabledStay Off Bios Exit Menu Page Beep Codes Flash UtilityMemory, Video, CPU Bios Post Code Code Beeps / DescriptionApic Code Beeps / Description Glossary Page Page Page Page Page Returning Merchandise for Service Technical SupportDocument # D1681-101
Related manuals
Manual 77 pages 23.79 Kb