Tyan Computer S2877 warranty Installing the Memory

Page 29

2.10 - Installing the Memory

Before attempting to install any memory, make sure that the memory you have is compatible with the motherboard as well as the processor.

The following diagram shows common types of DDR SDRAM modules:

Here are a few key points to note before installing memory into your Tiger K8WE:

Always install memory beginning with CPU1 DIMMA1.

In order to access memory on CPU2, both processors must be installed.

Single, pairs are supported on CPU1, four modules is also supported on CPU2.

Configure memory symmetrically on each CPU for best performance.

AMD OpteronTM processors support 64bit (non-interleaved) or 128bit (interleaved) memory configurations

At least ONE Registered DDR SDRAM module must be installed for the system to turn on and POST (power on self test)

128MB, 256MB, 512MB, 1GB, 2GB and 4GB* Registered DDR400/333/266 DDR memory modules are supported

All installed memory will be automatically detected

The Tiger K8WE supports up to 24GB* with two CPU’s installed.

*Not validated at time of print

29

http://www.tyan.com

Image 29
Contents Version CopyrightTrademark Bios Table of Contents IntroductionBoard Installation Page Congratulations Hardware SpecificationsExpansion Slots Integrated FireWire Ieee 1394A Controller Anrf version onlyIntegrated I/O Ports Back Panel I/O PortsOS Operating System Support Software SpecificationsPage Board Installation Board Image Tiger K8WE S2877 Block Diagram Block DiagramBoard Parts, Jumpers and Connectors Jumper Legend Jumper/Connector Function SettingsClear Cmos Header J112 DefaultFront Panel Header J139 Function Chassis Intrusion Header J77 4 *FireWire IEEE1394A Enable/Disable Jumper *J147Pin-2 Pin-1Open Pin3 and Pin4 5 *FireWire IEEE1394A Pin Header *J148/*J149Buzzer/External Speaker Header J14 USB 2.0 Front Panel Headers J25/J140 7 COM2 Connector J42Open Closed Keyboard Lock Connector J13Gigabit LAN1/**LAN2 Front Panel Header J2/ **J3 S2877G2NR version11 **VGA ATI Rage XL Enable/ Disable Jumper **J85 13 *Front Panel Audio Header *P53 CPU FAN Connector J9/J37Chassis 3-pin FAN Connectors J36/J10 Chassis 4-pin FAN Connector J47CPU1 FAN CPU2 FAN 17 3-pin or 4-pin fan support selection jumper J5Installing the Processors Heatsink Retention Frame Installation Thermal Interface Material Type a CAM Lever Type Installation Heatsink Installation ProceduresType B Screw Retention Type Heatsink Finishing Installing the Heatsink Tips on Installing Motherboard in Chassis Installing the Memory CPU1 CPU2 DIMM-A1 DIMM-A2 DIMM-B1 DIMM-B2 Memory Installation Procedure Attaching IDE Drive Cable Attaching Drive CablesPage Installing Add-In Cards Onboard LAN LED Color Definition Connecting External DevicesTips on modifying I/O shielding for Anrf and G2NR version Installing the Power SupplyFinishing Up Applying power to the boardPage To select an item Bios Setup UtilityGetting Help Bios Menu BarBios Legend Bar Feature Option Description Bios Main MenuMenu Item Bios Advanced MenuHammer Configuration Sub-Menu Integrated Devices Sub-Menu DisabledAuto LimitNV Configuration Feature Option Description DisabledEnabled PCI Configuration Sub-Menu PCI Device, Slot # 1 ,2,3 Add On Onboard Device ControlAvailable PCI/PNP ISA UHB Region ExclusionPCI/PNP ISA IRQ Resource Exclusion Feature Option Description AvailableBoth IDE Configuration Sub-MenuOther Standard Primary Master/Slave, Secondary Master/SlaveFloppy Configuration Sub-Menu Normal 6 I/O Device Configuration Sub-Menu3F8 378 Hardware Monitor Sub-MenuOutput only Primary19200 Console Redirection Sub-Menu38400 57600 115200 VT100~255 Watchdog Timer Option Sub-MenuDirect Memory Bios Memory MenuUshc Security MenuUser Bios Boot MenuALL PCI Scsi Boot Device PriorityEnabled Power MenuStay Off Bios Exit Menu Page Memory, Video, CPU Beep CodesFlash Utility Code Beeps / Description Bios Post CodeApic Code Beeps / Description Glossary Page Page Page Page Page Technical Support Returning Merchandise for ServiceDocument # D1681-101
Related manuals
Manual 77 pages 23.79 Kb